SATO HT200e Operator's Manual page 44

SECTION 2: INSTALLATION AND SETUP
PROCESS ON THE SCREEN FOR TRANSFER OF TABLE DATA
Ｐ Ａ Ｒ Ａ Ｍ Ｅ Ｔ Ｅ Ｒ Ｃ Ｏ Ｐ Ｙ
1
Ｐ Ｒ Ｉ Ｎ Ｔ Ｅ Ｒ ← → Ｃ Ａ Ｒ Ｄ
[ ]
←
Ｄ Ａ Ｔ Ａ Ｓ Ｔ Ｏ Ｒ Ｅ ／ Ｒ Ｃ Ａ Ｌ Ｌ
2
Ｐ Ｒ Ｉ Ｎ Ｔ Ｅ Ｒ ← → Ｈ Ｏ Ｓ Ｔ
[ ]
←
Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ Ｓ Ｔ Ｒ ／ Ｒ Ｃ Ａ Ｌ Ｌ
3
Ｐ Ｒ Ｉ Ｎ Ｔ Ｅ Ｒ ← → Ｈ Ｏ Ｓ Ｔ
[ ]
←
Ｆ Ｏ Ｎ Ｔ Ｓ Ｔ Ｏ Ｒ Ｅ ／ Ｒ Ｃ Ａ Ｌ Ｌ
4
Ｐ Ｒ Ｉ Ｎ Ｔ Ｅ Ｒ ← → Ｈ Ｏ Ｓ Ｔ
Ｔ Ａ Ｂ Ｌ Ｅ Ｓ Ｔ Ｒ ／ Ｒ Ｃ Ａ Ｌ Ｌ
5
Ｐ Ｒ Ｉ Ｎ Ｔ Ｅ Ｒ ← → Ｈ Ｏ Ｓ Ｔ
Ｄ Ａ Ｔ Ａ Ｓ Ｅ Ｎ Ｄ ／ Ｒ Ｅ Ｃ
6
Ｈ Ｔ → Ｈ Ｏ Ｓ Ｔ
Ｈ Ｔ → Ｈ Ｏ Ｓ Ｔ Ｓ Ｅ Ｎ Ｄ Ｏ Ｋ ？
Or:
Ｈ Ｏ Ｓ Ｔ → Ｈ Ｔ Ｒ Ｅ Ｃ
Ｓ Ｅ Ｎ Ｄ Ｉ Ｎ Ｇ
Ｉ Ｔ Ｅ Ｍ
Or:
Ｒ Ｅ Ｃ Ｅ Ｉ Ｖ Ｉ Ｎ Ｇ
Ｉ Ｔ Ｅ Ｍ
Table data that are transferred from a host computer will be registered in a printer. The data registered in the
printer can be transferred to the host.
Note: When table data is transferred, on-line cable must be connected to the host before turning the power "ON".
Page 2-26
6 + Power "ON"
Ｈ Ｏ Ｓ Ｔ → Ｈ Ｔ
Ｙ ／ Ｎ
Ｙ ／ Ｎ
:
０ ０ ０ １
:
０ ０ ０ １
Press [ENTR], so that it goes to the screen for the
selection of copying print parameter.
Press [
→
[ ]
→
Press [ENTR], so that it goes to the screen for the
selection of transferring print parameter.
Press [
←
[ ]
→ Press [
→
Press [ENTR], so that it goes to the screen for the
selection of transfering preset.
Press [
←
[ ]
→
Press [
→
Press [ENTR], so that it goes to the screen for the
selection of transfering font.
Press [
←
Press [ENTR], so that it goes to the screen for the
selection of transfering table data.
Press [
←
For the transfering direction, select [
and press [ENTR] to go to the screen for the
confirmation of receiving-and-sending.
Press [ENTR]:
Ｏ Ｋ ？
"Y" is to start receiving and sending.
"N" is to return to the process No. 5.
When sending one item is complete, the number o
items will be added.
After sending, it returns to the process No. 5.
When receiving one item is complete, the number o
items will be added.
After receiving, it returns to the process No. 5.
], so that it goes to the process No. 2.
], so that it returns to the process No. 1.
], so that it goes to the process No. 3.
], so that it returns to the process No. 2.
], so that it goes to the process No. 4.
], so that it returns to the process No. 3.
], so that it returns to the process No. 4.
] and [ ],
← →
SATO HT200e