SATO HT200e Operator's Manual page 100

SECTION 5 PRESET, TABLE DATA
：
MASTER LABEL PRINTING FOR PRESET DATA
Ｆ Ｏ Ｒ Ｍ Ａ Ｔ Ｎ ｏ
1 ［ ・ ・ ］
［ Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ ］
2 Ｐ Ｒ Ｉ Ｎ Ｔ
Ｄ Ｅ Ｌ Ｄ Ｕ Ｍ Ｐ Ｍ Ａ Ｓ Ｔ Ｅ Ｒ
［ Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ ］
3 Ｐ Ｒ Ｉ Ｎ Ｔ
Ｄ Ｅ Ｌ Ｄ Ｕ Ｍ Ｐ Ｍ Ａ Ｓ Ｔ Ｅ Ｒ
［ Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ ］
4 Ｐ Ｒ Ｉ Ｎ Ｔ Ｓ Ｔ Ｒ
Ｄ Ｅ Ｌ Ｄ Ｕ Ｍ Ｐ Ｍ Ａ Ｓ Ｔ Ｅ Ｒ
［ Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ ］
5 Ｐ Ｒ Ｉ Ｎ Ｔ Ｓ Ｔ Ｒ Ｍ Ｏ Ｄ Ｉ Ｆ Ｙ
Ｄ Ｅ Ｌ Ｄ Ｕ Ｍ Ｐ Ｍ Ａ Ｓ Ｔ Ｅ Ｒ
［ Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ ］
6 Ｐ Ｒ Ｉ Ｎ Ｔ Ｓ Ｔ Ｒ Ｍ Ｏ Ｄ Ｉ Ｆ Ｙ
Ｄ Ｅ Ｌ Ｄ Ｕ Ｍ Ｐ
［ Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ ］
7 Ｐ Ｒ Ｉ Ｎ Ｔ Ｓ Ｔ Ｒ Ｍ Ｏ Ｄ Ｉ Ｆ Ｙ
Ｄ Ｅ Ｌ Ｄ Ｕ Ｍ Ｐ
Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ Ｎ Ｏ ． Ｉ Ｎ Ｐ Ｕ Ｔ
8 ・ ・ ・ ・ ― ・ ・ ・ ・ Ｍ Ａ Ｓ Ｔ Ｅ Ｒ
Ｐ Ｒ Ｉ Ｎ Ｔ Ｉ Ｎ Ｇ
9
Page 5-8
Ｈ Ｔ ２ ０ ０ ｅ
[RCL]
Ｓ Ｔ Ｒ Ｍ Ｏ Ｄ Ｉ Ｆ Ｙ
[ ]
→
Ｓ Ｔ Ｒ Ｍ Ｏ Ｄ Ｉ Ｆ Ｙ
[ ]
→
Ｍ Ｏ Ｄ Ｉ Ｆ Ｙ
[ ]
→
[ ]
→
Ｍ Ａ Ｓ Ｔ Ｅ Ｒ
[ ]
→
Ｍ Ａ Ｓ Ｔ Ｅ Ｒ
[ENTR]
[ENTR]
Press [RCL], so that it goes from the modes of the
print to the preset.
The screen for the selection of preset printing will
be displayed: Press [
→
screen for the process No. 3.
The screen for the selection of preset storing will
be displayed: Press [
→
screen for the process No. 4.
The screen for the selection of preset modification
will be displayed: Press [
screen for the process No. 5.
The screen for the selection of preset deletion will
be displayed: Press [
→
screen for the process No. 6.
The screen for the selection of preset dump will be
displayed: Press [ ] , so that it goes to the screen
→
for the process No. 7.
The screen for the selection of preset master will
be displayed: Press [ENTR], so that it goes to the
entry of preset number.
The preset No. that is required to print master label
can be entered: Press [ENTR], so that it prints
master label for the preset specified.
Note that if [ENTR] is pressed without entering a
preset No., the preset data registered will be
printed from the beginning.
While master label is being printed, the screen of
the process No. 9 remains displayed. When print is
complete, it returns to the process No. 8.
], so that it goes to the
], so that it goes to the
], so that it goes to the
→
], so that it goes to the
SATO HT200e