SATO HT200e Operator's Manual page 97

MODIFICATION OF PRESET DATA
Ｆ Ｏ Ｒ Ｍ Ａ Ｔ Ｎ ｏ
1
［ ・ ・ ］
［ Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ ］
2 Ｐ Ｒ Ｉ Ｎ Ｔ
Ｄ Ｅ Ｌ
［ Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ ］
3 Ｐ Ｒ Ｉ Ｎ Ｔ
Ｄ Ｅ Ｌ
［ Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ ］
4 Ｐ Ｒ Ｉ Ｎ Ｔ Ｓ Ｔ Ｒ
Ｄ Ｅ Ｌ
Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ Ｎ Ｏ ． Ｉ Ｎ Ｐ Ｕ Ｔ ＊
5 ・ ・ ・ ・
［ Ｉ Ｔ Ｅ Ｍ
6
・ ・ ・ ・ ・ ・ ・ ・ ・
［ Ｐ Ｒ Ｉ Ｃ Ｅ
7
￡ ・ ・ ・ ・ ・ ・
Note: Where asterisk mark or "*" can be seen in the upper right on the screen, entry by scanner can be made
possible.
SATO HT200e
Ｈ Ｔ ２ ０ ０ ｅ
[RCL]
Ｓ Ｔ Ｒ Ｍ Ｏ Ｄ Ｉ Ｆ Ｙ
Ｄ Ｕ Ｍ Ｐ Ｍ Ａ Ｓ Ｔ Ｅ Ｒ
[ ]
→
Ｓ Ｔ Ｒ Ｍ Ｏ Ｄ Ｉ Ｆ Ｙ
Ｄ Ｕ Ｍ Ｐ Ｍ Ａ Ｓ Ｔ Ｅ Ｒ
[ ]
→
Ｍ Ｏ Ｄ Ｉ Ｆ Ｙ
Ｄ Ｕ Ｍ Ｐ Ｍ Ａ Ｓ Ｔ Ｅ Ｒ
[ENTR]
＜ Ｍ Ｏ Ｄ Ｉ Ｆ Ｙ ＞
[ENTR]
］
[ENTR]
］
[ENTR]
SECTION 5
Press [RCL], so that it goes from the modes of the
print to the preset.
The screen for the selection of preset printing will
be displayed: Press [
→
screen for the process No. 3.
The screen for the selection of preset storing will be
displayed: Press [ ], so that it goes to the screen
→
for the process No. 4.
The screen for the selection of preset modification
will be displayed: Press [ENTR], so that it goes to
the entry of preset number.
The preset No. that is required to print can be
entered: Press [ENTR], so that it displays the pre-
set data specified.
Since the contents for data will be changed,
based on the format No. retrieved, enter data
required to modify for each field, and press
[ENTR].
Note: Entry by scanner is available when ITEM
is input.
In the last field, press [ENTR] so that data will
be replaced.
PRESET, TABLE DATA
：
], so that it goes to the
Page 5-5