SATO HT200e Operator's Manual page 37

Ｈ Ｅ Ａ Ｄ Ｃ Ｈ Ｅ Ｃ Ｋ
10
Ｏ Ｎ
Ｂ Ｅ Ｅ Ｐ Ｓ Ｅ Ｔ Ｔ Ｉ Ｎ Ｇ
11
Ｏ Ｎ
For protocode setting:
Ｐ Ｒ Ｏ Ｔ Ｏ Ｃ Ｏ Ｄ Ｅ
12
Ｓ Ｔ Ａ Ｎ Ｄ Ａ Ｒ Ｄ
Ｎ Ｏ Ｎ － Ｓ Ｔ Ａ Ｎ Ｄ Ａ Ｒ Ｄ
Ｎ Ｏ Ｎ － Ｓ Ｔ Ａ Ｎ Ｄ Ａ Ｒ Ｄ
13
Ｄ Ｅ Ｆ Ａ Ｕ Ｌ Ｔ
Ｎ Ｏ Ｎ － Ｓ Ｔ Ａ Ｎ Ｄ Ａ Ｒ Ｄ
14 :
Ｓ Ｔ Ｘ
Ｃ Ｏ Ｄ Ｅ Ｐ Ａ Ｇ Ｅ Ｓ Ｅ Ｔ
15
８ ５ ８
SATO HT200e
Ｏ Ｆ Ｆ
Ｏ Ｆ Ｆ
Ｕ Ｓ Ｅ Ｒ － Ｓ Ｅ Ｔ
０ ２ Ｈ Ｅ Ｘ
A table of PROTO CODE:
Name
STX
ETX
ESC
EOT
SOH
Note 1) Default code for non-standard is standard code.
８ ５ ２
SECTION 2: INSTALLATION AND SETUP
Select with [
(ON: Head check is available.)
(OFF: Head check is NOT available.)
Select with [
(ON: If selected, sound that keys are entered can
be heard.
(OFF: If selected, keys that are entered make
sound in silence.)
Select Standard or not with [
and press [ENTR]. Where Standard is determined,
it goes to the process No. 15. Whereas Non-
standard is chosen, it goes to the process No. 13.
Code can be chosen for Non-standard:
Select DEFAULT, and press [ENTER] so that it will
terminate the setting for PROTO CODE. Where
User-set is selected, follow the next screen.
For User-set, STX screen initially appears:
Enter Hex data and value in 2 digits for the STX
code.
Enter value from 0 to 9 with keypad, and use arrow
(up and down) for A to F. Note that any other keys ar
not available. When finishing STX setting, press
[PGUP] key so that it goes to ETX setting screen.
The table in the following shows the order of code
that will be set.
When last code has been set, it will terminate
PROTO CODE to be set.
Standard Non-standard See Note 1.
02H Setting by user is available.
03H Setting by user is available.
1BH Setting by user is available.
04H Setting by user is available.
01H Setting by user is available.
Code page can be selected:
858: Code page 858
852: Code page 852
] and [ ], and press [ENTR].
← →
] and [ ], and press [ENTR].
← →
] [ ] [
↓ ↑
] and [ ] ,
← →
Page 2-19