Oce COLOR SYSTEM 110 Operator's Manual page 5

Using This Manual
Operation Procedures
In this manual, the following marks are used in the explanation of the operating procedures,
cautions, notes, and related functions.
Indicates the title of the topic
being explained on this page.
(The page depicted above is for example purposes only, and is not actually found in this manual.)
Indicates a note containing information you should be aware of regarding
the operation, or else an explanation of restrictions. Always read these
items in order to operate the copier properly.
Indicates a function that can be used when the copier is equipped with the optional
IP-ED Board-B1.
Indicates a function that can be used when the copier is equipped with the optional
Editor-F1. The Editor-F1 is referred to as the Editor hereinafter.
Indicates a function that can be used when the copier is equipped with the optional
Recirculating Document Feeder RDF-E2. The Recirculating Document Feeder RDF-E2
is referred as the Feeder hereinafter.
Indicates a function that can be used when the copier is equipped with the optional
Stapler Sorter-F1. The Stapler Sorter-F1 is referred as the Sorter or Stapler Sorter
hereinafter.
Indicates a function that can be used on the CS 115.
Indicates a function that can be used when the copier is equipped with the optional Film
Projector-D1.
Indicates a function that can be used when the copier is equipped with the optional
CS 110/115 NC
Océ CS 110/115 NC.
Example displays used in this manual assume that the copier is equipped with all possible options.
The actual displays will vary with the attached options.
IV
Indicates the title and page number of a reference item.
: User's Manual
: Quick Index
Using the Control Panel Keys
1-5
Interrupt
Editor
When the key is pressed, the Interrupt mode is activated. Press this key to stop
the current copy job and begin another copy job.
The following modes and settings can be specified in the Interrupt mode:
· Copy quantity · Preset Zoom · Center shift
· Original Type · Zoom · One Touch Color
· Copy Exposure Adjustment · Auto Zoom · Color Balance
· Paper Selection · XY Zoom · Image Quality Adjustment
· ACS/Full Color/Black · Zoom Program · Sharpness
· Original Size Recognition · Entire Image
The Interrupt mode cannot be selected during a Composition copy job. Also the Interrupt mode
cannot be selected during another interrupted copy, recovering, or Auto Start copy job.
When Placing an Original on the Platen Glass
If a department ID and/or a user
ID are already registered, the
1 Press the key.
screen appears to prompt you to
enter the registered ID number.
When the key is pressed, its indicator starts blinking.
Enter the correct department ID
number and user ID number. For
Reset
details, see "Entering the
1 2 3
Department ID Number and User
Guide ID Number," on p. 2-4.
4 5 6
Additional Functions To cancel the interrupt copy
7 8 9
during setting, press the
Clear
Interrupt
ID 0 C
When the current copy job has stopped, the message
"Ready to perform interrupt job." appears on the Touch
Panel Display. The blinking key indicator is retained
ON (Interrupt mode).
Basic
2-12
Mode
Indicates options, etc.,
required to use this function.
Using the Control Panel Keys
2
Remove the original for the
current copy job from the platen
glass.
3
Place the original for the interrupt
copy job on the platen glass.
4 Program the necessary copy
settings.
5 Press the (Start) key.
During the interrupt copy job, the message "Performing
interrupt job." appears on the Touch Panel Display.
6 When the interrupt copy is
completed, press the [No] key.
key.
You cannot resume the previous copy job without
canceling the Interrupt mode. Upon completion of the
interrupt copy job, be sure to press the key to cancel
the Interrupt mode.
7
Remove the original for the
interrupt copy job from the platen
glass.
8
Place the previous original on the
platen glass.
9
Press the (Start) key.
The copier resumes the interrupted copy job.
Interrupt
If you are copying from the platen
glass, temporarily remove the
original from the platen glass. If
you are copying from the original
tray of the optional Feeder,
2
perform the interrupt copy job
without removing the originals on
the tray. If you remove the
originals from the original tray,
the previous copy job cannot be
continued after the Interrupt
mode is canceled.
Indicates that this is
To make another interrupt copy,
press the [Yes] key.
a note concerning
operation or an
explanation of a
related function.
Step 8 applies if you were
continuously making copies from
the platen glass.
Basic
2-13
Mode