Table of Contents
Advertisement
Table 19: CompactPCI Rear I/O Connector J3 Signals for CP6007-SA
The RIO_XXX signals are power supply OUTPUTS to supply the rear I/O module with power.
These pins MUST NOT be connected to any other power source, either within the backplane
itself or within a rear I/O module.
Failure to comply with the above will result in damage to your board.
SIGNAL
DESCRIPTION
SPA
COMA signaling (RS-232)
SPB
COMB signaling (RS-422/RS-232)
VGA
Graphic signaling
USB0 to USB3
USB port signaling
SPEAKER
Standard PC speaker
FAN
Fan speed sensoring
DEBUG
Debug output
LPa
Rear I/O LAN Port A
LPb
Rear I/O LAN Port B
GPIO
General purpose digital input/output; 3.3 V only
COMA can be used either on the front panel or on the rear I/O. It is not possible to use COMA
on the front panel and on the rear I/O simultaneously.
Table 20: 64-bit CompactPCI Rear I/O Connector J3 Pinout for CP6007-RA
PIN
Z
A
19
NC
RIO_5V
18
NC
LPa_DA+
17
NC
LPa_DB+
16
NC
LPb_DA+
15
NC
LPb_DB+
14
NC
LPa:LINK
13
NC
LPa:ACT
12
NC
LPc:DA+
11
NC
LPc:DB+
10
NC
USB1:VCC
9
NC
USB1:D-
8
NC
USB0:D-
7
NC
RIO_3.3V
6
NC
VGA:RED
5
NC
VGA:BLUE
4
NC
LPd:DA+
3
NC
LPd:DB+
2
NC
SPA:RI
1
NC
SPA:RTS
www.kontron.com
B
C
RIO_5V
RIO_3.3V
LPa_DA-
GND
LPa_DB-
GND
LPb_DA-
GND
LPb_DB-
GND
LPb:LINK
LPab:CT1
LPb:ACT
LPcd:CT1
LPc:DA-
GND
LPc:DB-
GND
USB0:VCC
GND
USB1:D+
GND
USB0:D+
GND
GPI0
GPI1
VGA:GREEN
VGA:SDA
VGA:HSYNC
VGA:VSYNC
LPd:DA-
SPB:TX-/TX
LPd:DB-
SPB:RX-/CTS
SPA:DTR
SPA:CTS
SPA:RX
SPA:DSR
CP6007-SA, CP6007-RA – User Guide, Rev. 1.0
D
E
RIO_+12V
RIO_-12V
LPa_DC+
LPa_DC-
LPa_DD+
LPa_DD-
LPb_DC+
LPb_DC-
LPb_DD+
LPb_DD-
LPc:LINK
RSV
(FAN:SEN2)
LPc:ACT
RSV
(FAN:SEN1)
LPc:DC+
LPc:DC-
LPc:DD+
LPc:DD-
USB3:VCC
USB2:VCC
USB3:D-
USB3:D+
USB2:D-
USB2:D+
GPI2
SPEAKER
DEBUG:CLK
DEBUG:DAT
VGA:SCL
LPd:DC+
SPB:TX+/RTS
LPd:DC-
SPB:RX+/RX
LPd:DD+
SPA:TX
LPd:DD-
SPA:DCD
RIO_ID1
F
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
// 46
Advertisement
Table of Contents
