FUTABA 32MZ-WC Full Manual page 203

*The current condition number of CGY is displayed.
*The setting with "C#" display can be set for each condition.
1. Use the "C#" button to select the condition number.
2. Next, adjust value of the condition selected by the r a t e
button.
For functions that can set conditions in
this manual, mark
Cond
(13) STK. Dir ELE: Elevator operation
Load the direction of elevator into the gyro.
[Setting method] Touch the "Up" button to enter the setting mode.
"Sure?" Is displayed. Operate the elevator stick fully to the up. If you
touch the [Yes] button, the operation direction of elevator is memorized.
WARNING
Verify that the CGY compensates in the correct direction before
flight. If the compensation direction is incorrect the model will roll or
pitch uncontrollably even before it leaves the ground.
＜ Model Menu (Helicopter) ＞
203
Swash Basic Swash Basic
(6)AIL, ELE, PIT. Ntr:
Adjust the neutral position of the swash servo (aileron, elevator, pitch,
second elevator). The second elevator (ELE2) is displayed only when the
swash type is H4-xx.
(7) SWS. Dir: Swash direction setting
This selects the aileron, elevator and collective pitch direction. Reverse
the direction when the stick movement and swash movement are op-
posite. Each time you press the +/- button, the polarity switches.
(8) SWS. Rate: Rate adjustment
The Swash Rate settings are used to set a known base cyclic throw for
the gyro to calculate the compensations and gain scale. This value does
not represent the total cyclic throw, but rather shows the gyro a known
point for the gyro to understand the helicopters geometry. It is important
to note that one setting applies to both roll and pitch axes; they are not
individually adjusted.
(DUAL RATES MUST BE 100)
-Suggested amount of base cyclic pitch
*800 size ‒ 10 degrees
*700 size ‒ 9 degrees
*600 - 550 size ‒ 8 degrees
*500 size ‒ 7 degrees
*450 and below- 6 degrees
(9) PIT. Rate: Rate adjustment
is written.
The [PIT.Rate] is the amount of collective pitch travel allowed. A good
starting range for Sport, 3D and F3C is +/-10 to +/-12 degrees.
(10) SWS. Ring
This parameter is used to set the total maximum of cyclic throw as well as
limit the swash travel to prevent binding of the swash plate servos when
the control stick is moved toward a corner (for example, full right and full
aft cyclic).
(11) AGy. Dir: Aileron (roll) Gyro direction
This parameter controls which direction the CGY (roll / pitch axis) will
compensate when the helicopter rolls (pitches). Pick the helicopter up
and roll the helicopter to the right. The CGY should compensate by add-
ing left cyclic to the swash plate. (Pick the helicopter up and rotate the
nose of the helicopter downward. The CGY should compensate by add-
ing aft cyclic to the swash plate.)
If the CGY compensates in the wrong direction, then it will be necessary
to reverse the compensation direction setting.
(12) STK. Dir AIL: Aileron operation
Load the direction of Aileron into the gyro.
[Setting method] Touch the "Right" button to enter the setting mode.
"Sure?" Is displayed. Operate the Aileron stick fully to the right. If you
touch the [Yes] button, the operation direction of Aileron is memorized.
Servo neutral adjustment
Setting ranges: +240 ~ -240 Initial value: 0
Setting ranges: 0 ~ 100% Initial value: 50%
Setting ranges: 0 ~ 100 Initial value: 50%
Setting ranges: 50 ~ 100% Initial value: 130%
EGy. Dir: Elevator (pitch) Gyro direction
WARNING
Verify that the CGY compensates in the correct direction before
flight. If the compensation direction is incorrect the model will roll or
pitch uncontrollably even before it leaves the ground.
Be sure to set this aileron motion direction and elevator motion direction
so that F/F mixing (Ele Comp and Rud. F/F menu) works effectively. Also,
please perform this operation after setting the direction of operation.
Cond
Cond
Cond