Setting The Conversion Mode; Restarting Link Training; Audio Input Port Settings; Audio Mode Setting - Lightware MX2-8x8-DH-4DPio-A User Manual

   
9. LW3 Programmers' Reference
9.6.5. Setting the Conversion Mode
INFO:
DisplayPort signals over 18Gbps will be converted down by either truncating bit depth or by
converting RGB signal to YCbCr 4:2:2 12-bit signal based on user selection. The second option will not
reduce the color depth, instead it results in loss of chroma information.
Command and Response #colorspace
SET·/MEDIA/PORTS/VIDEO/<in>/SETTINGS.Conversion=<conversion_mode>
ç
pw·/MEDIA/PORTS/VIDEO/<in>/SETTINGS.Conversion=<conversion_mode>
æ
Parameters
Identifier Parameter description
<conv_mode> Conversion mode
Example
ç SET /MEDIA/PORTS/VIDEO/I1/SETTINGS.Conversion=OFF
æ pw /MEDIA/PORTS/VIDEO/I1/SETTINGS.Conversion=OFF
9.6.6. Restarting Link Training
This method is equal with pulling the DP connector out and plugging it in again.
Command and Response #linktraining
ç CALL·/MEDIA/PORTS/VIDEO/<in>/SETTINGS:dpLinkTrain()
æ mO·/MEDIA/PORTS/VIDEO/<in>/SETTINGS:dpLinkTrain=
Example
ç CALL /MEDIA/PORTS/VIDEO/I1/SETTINGS:dpLinkTrain()
æ mO /MEDIA/PORTS/VIDEO/I1/SETTINGS:dpLinkTrain=
Parameter values
OFF: The video signal is transmitted without any changing.
422: The video converter subsamples the 4:4:4 signal to 4:2:2.
420: The video converter subsamples the 4:4:4 signal to 4:2:0.
Applied firmware package: v1.9.0 | LDC software: v2.6.2b3
MX2 Standalone Matrix Switcher series – User's Manual
9.7. Audio Input Port Settings
The current setting can be queried by using the
DIFFERENCE:
Audio settings are available when there is an analog audio port beside the chosen video
port. -A or -Audio suffix in the model name refers to the analog audio feature (see the
table about the analog audio availability).
9.7.1. Audio Mode Setting
Command and Response #audio
SET·/MEDIA/PORTS/VIDEO/<in>/ANALOGAUDIO.AudioMode=<audio_mode>
ç
pw·/MEDIA/PORTS/VIDEO/<in>/ANALOGAUDIO.AudioMode=<audio_mode>
æ
Parameters
Identifier
<audio_mode> The current audio mode OFF: no audio in the video stream.
Example
ç SET /MEDIA/PORTS/VIDEO/I1/ANALOGAUDIO.AudioMode=ANALOG
æ pw /MEDIA/PORTS/VIDEO/I1/ANALOGAUDIO.AudioMode=ANALOG

INFO: In case of -Audio suffixed models, modifying the /MEDIA/PORTS/VIDEO/<in>/ANALOGAUDIO.
AudioMode=<audio_mode>
AudioMode=<audio_mode>
9.7.2. Analog Audio Input Level Settings
9.7.2.1. Setting the Balance (the Exact Value)
Command and Response
SET·/MEDIA/PORTS/VIDEO/<in>/ANALOGAUDIO.Balance=<bal_value>
ç
pw·/MEDIA/PORTS/VIDEO/<in>/ANALOGAUDIO.Balance=<bal_value>
æ
Parameters
The <bal_value> can be set between -100 and 100 (0=center, +100=right, -100=left).
Example
ç SET /MEDIA/PORTS/VIDEO/I1/ANALOGAUDIO.Balance=50
æ pw /MEDIA/PORTS/VIDEO/I1/ANALOGAUDIO.Balance=50
GET command in all cases.
#analogaudio #volume #balance #gain #mute #unmute
Parameter description Parameter values
HDMI: the original audio is embedded in the video stream
ANALOG: the analog audio of the input port is embedded in the
video stream.
property will change the /MEDIA/PORTS/VIDEO/<in>/EMBEDDEDAUDIO.
property.
87
Model Comparison