Fuel Dispensers TATSUNO EUROPE ‐ Installation and User Manual , revision 10, January 2022
2.2. CERTIFICATES & APPROVALS
TATSUNO EUROPE dispensers comply with all European standards of metrology and safety. Table 7 contains a
list of valid European certificates in terms of metrology and safety.
Table 7 ‐ MID & ATEX certificate of dispensers
#
Type designation
1
SHARK BMP5xx.Sx
2
OCEAN BMP4xxx.Oxx
3
SHARK BMP5xx.Sx /LPG
4
OCEAN BMP4xxx.Oxx /LPG
5
SHARK BMP5xx.Sx /AdB
6
SHARK BMP5xx.Sx /AdB&Die
7
OCEAN BMP4xxx.Oxx /AdB
8
OCEAN BMP4xxx.Oxx /WSE
9
OCEAN BMP4xxx.Oxx /CNG
10
OCEAN BMP4xxx.OEx+MOD4xxx.Oxx/xxx
*
Note: For CNG dispensers there is no European directive as for liquid dispensers (MID 2014/32/EU), therefore the dispensers have been tested
and certified according to OIML R139 international recommendation. Typical metrological certification is conducted in each state according to
their internal rules.
2.2.1. METROLOGY
All series of dispensers have been tested and certified by the Czech Metrology Institute in Brno, notified
European body No. 1383. The conformity assessment for liquid dispensers – see Table 7, devices 1 to 9 – was
carried out by procedures "B" (type examination) + "D" (quality assurance of the production process), according
to the Government Decree No. 120/2016 Coll., which stipulates technical requirements for measuring
instruments, and which implements the European Parliament and Council Directive 2014/32/EU in the Czech
Republic. For all devices, OIML R117 and OIML D11 tests were performed and an EU type certificate (so‐called
MID certificate) was issued.
The conformity assessment for compressed natural gas dispensers – see Table 7, device 10 – was carried out by
a type examination pursuant to the Act on Metrology No. 505/1990 Coll. and a Czech type certificate No. TCM
143/15‐5321 was issued. Type tests have been carried out in accordance with the international
recommendation OIML R139. Based on the type tests the OIML CERTIFICATE ISSUED UNDER SCHEME B No.
R139/2014‐B‐CZ1‐2018.01 has been issued for CNG dispensers.
The company TATSUNO EUROPE a.s. has obtained a Certificate of System Quality Management No. 0119‐
SJC006‐07 from The Czech Metrology Institute, thus fulfilling the eligibility prerequisite for declaration of type
conformity based on quality assurance of the production of measuring instruments according to Appendix No.
2, procedure „D" (Chapter 6) of the Government Decree No. 120/2016 Coll. The validity of the certificate is
checked by audits annually.
2.2.2. SAFETY
The dispensers have been tested and certified by the authorized body No. 210 ‐ Physical‐Technical Testing
Institute in Ostrava ‐ Radvanice, notified body No. 1026 for use in potentially explosive atmospheres according
to Directive 2014/34/EU. Dispensers were certified to comply with European standards for the construction of
dispensers and machinery located in potentially explosive areas – EN 13617‐1, EN 14678‐1, EN IEC 60079‐0, EN
ISO 80079‐36, EN 1127‐1. All dispensers and their parts located in potentially explosive areas are in compliance
Delivered medium
Gasoline, (bio)diesel, E85, AVGAS
Gasoline, (bio)diesel, E85, AVGAS
Liquefied propane‐butane (LPG)
Liquefied propane‐butane (LPG)
AdBlue®
Combined Diesel + AdBlue®
AdBlue®
Windshield washer fluid (WSE)
Compressed natural gas (CNG)
Combined dispenser
25
ATEX certificate
MID certificate
FTZÚ 03 ATEX 0022
TCM 141/07‐4491
FTZÚ 10 ATEX 0259
TCM 141/07‐4491
FTZÚ 03 ATEX 0025
TCM 141/07‐4493
FTZÚ 10 ATEX 0064X
TCM 141/07‐4493
FTZÚ 21 ATEX 0048X
TCM 141/07‐4492
FTZÚ 03 ATEX 0022
TCM 141/07‐4491 (4492)
FTZÚ 21 ATEX 0048X
TCM 141/07‐4492
A565‐18 (FTZÚ)
TCM 141/13‐5085
A484‐16 (FTZÚ)
R139/2014‐B‐CZ1‐2018.01
FTZÚ 10 ATEX 0065X
Acc. to configuration
*