Fuji Electric FE ZSS Instruction Manual page 69

Cross stack laser gas analyzer
Table of Contents

Advertisement

Analog Input
GasPress.(kPa)
Gas Temp.(℃)
Gas Flow(m/s)
O2
(vol%)
H2O
(vol%)
Air Purge(kPa)
Analog Input
GasPress.(kPa)
Gas Temp.(℃)
Gas Flow(m/s)
O2
(vol%)
H2O
(vol%)
Air Purge(kPa)
Analog Input
GasPress.(kPa)
Gas Temp.(℃)
Gas Flow(m/s)
O2
(vol%)
H2O
(vol%)
Air Purge(kPa)
Analog Input
GasPress.(kPa)
Gas Temp.(℃)
Gas Flow(m/s)
O2
(vol%)
H2O
(vol%)
Air Purge(kPa)
INZ-TN1ZSS-E
2007-4-1
12:00:00
Fixed
4mA
20mA
Fixed
00.00
00.00
10.00
Fixed
0027
0100
1000
Fixed
02.00
00.00
20.00
Fixed
20.00
00.00
21.00
Fixed
050.0
000.0
100.0
Alarm
4mA
20mA
No
005.0
000.0
100.0
Under
(
)
NT
2007-4-1
12:00:00
Fixed
4mA
20mA
Fixed
00.00
00.00
10.00
0027
0000
1000
CH1
Fixed
02.00
00.00
20.00
Fixed
20.00
00.00
21.00
Fixed
050.0
000.0
100.0
Alarm
4mA
20mA
No
005.0
000.0
100.0
Under
(
)
NT
2007-4-1
12:00:00
Fixed
4mA
20mA
Fixed
00.00
00.00
10.00
0027
0000
1000
CH1
Fixed
02.00
00.00
20.00
Fixed
20.00
00.00
21.00
Fixed
050.0
000.0
100.0
Alarm
4mA
20mA
No
005.0
000.0
100.0
Under
(
)
NT
2007-4-1
12:00:00
Fixed
4mA
20mA
Fixed
00.00
00.00
10.00
0027
0000
0500
CH1
Fixed
02.00
00.00
20.00
Fixed
20.00
00.00
21.00
Fixed
050.0
000.0
100.0
Alarm
4mA
20mA
No
005.0
000.0
100.0
Under
Select the channel (CH1 or CH2) connected to AI
terminal by the
lect from CH1 to CH6 when AI expansion board
is connected), and press the
The relations between channels are as follows;
AI1 = CH1, ......... AI6 = CH6.
Enter the temperature (°C) corresponding to 4mA
DC output of the output signal of the thermome-
ter. Change the numeric value by the
or the
key, and move the digits by the
key. Press the
input value.
Enter the temperature (°C) corresponding to
20mA DC output of the output signal of the ther-
mometer. Change the numeric value by the
key or the
key. Press the
input value.
Implement the same procedure as for the sensor
setting of pressure gauge, flow meter, oxygen
analyzer (O
) or the moisture meter (H
2
- 59 -
key or the
key (se-
NT
key.
NT
key to validate the set
key, and move the digits by the
NT
key to validate the set
O).
2
key

Advertisement

Table of Contents
loading

Table of Contents