1 S); Schwingungsdämpfer; Dimensions And Integration In The Control Identical To; Se-E1 - Bitzer CSH6553-35Y Operating Instructions Manual

5.4.2 CM-SW-01
Verdichter parallel zur Schiffslängsachse einbauen und
• entweder waagrecht zum Wasserspiegel
Standard for all CSW105 compressors
• oder um 10° in Verdichterlängsrichtung geneigt, mit
The compressor module integrates the entire electronic
dem Motor nach unten
periphery of the compressor: It allows monitoring the
Voraussetzung dafür: Das Ölniveau bleibt in Betrieb
essential operating parameters of the compressor: mo-
im Bereich des oberen Schauglases. In der folgen-
tor and discharge gas temperature, phase and rotation
den Abbildung ist es als breiter grauer Strich ange-
direction monitoring, oil supply and application limits
deutet.
and thus protects the compressor from operation under
critical conditions. For further information, see Tech-
nical Information ST-150.
NOTICE
!
!
The compressor module may be damaged or
fail!
Never apply any voltage to the terminals of CN7
to CN12 – not even for test purposes!
The voltage applied to the terminals of CN13
must not exceed 10 V!
The voltage applied to terminal 3 of CN14 must
not exceed 24 V! Do no apply voltage to the
other terminals!
The following components are completely installed and
wired in the state of delivery:
• Slider position indicator.
• Oil monitoring (OLC-D1).
Abb. 3: Zulässige Neigungswinkel des Schiffes am Beispiel CSH85
• Solenoid valves for capacity control and V
• Discharge gas temperature sensor.
• Low pressure and high pressure transmitter.
Modification to these components or their wiring is not
required and should not be done without consulting
BITZER.
The following components are not installed and wired in
the state of delivery and need to be connected:
• Motor temperature monitoring (PTC sensor in motor
winding).
1
• Phase monitoring (in case of a phase failure or inad-
missibly high phase asymmetry).
Abb. 4: Schwingungsdämpfer
The compressor module internally supplies voltage to
Schwingungsdämpfer
the peripheral devices (solenoid valves, oil monitoring
device and slider position indicator) and to the terminal
1 CS.9553 .. CS.9573,
strips CN7 to CN12.
CSH96: blau
CSW10593: gelb
Please refer to the Technical Information ST-150 for in-
formation on all connections.
SB-170-9
SB-170-9
SB-170-9 RUS
7,5°
5°
0°
5°
7,5°
17,5°
15°
15°
17,5°
.
i
2
2 CS.9553 .. CS.9573,
CSH96: gelb
CSW10593: gelb
5.4.3 SE-i1
Aufstel- Neigung in Längs-
lung richtung
This protection device with extended monitoring func-
statisch
tions can be used as an option for all HS.53 .. HS.85
compressors and CSH and CSW compressors.
waag- ±5°
Monitoring functions:
recht
• Temperature monitoring.
+10° ge- ±15°
• Monitoring of the PTC control circuit to detect any neigt
short-circuit or line break/sensor failure.
Tab. 3: Maximale Neigungswinkel des Schiffes
• Rotation direction monitoring.
• Monitoring of phase failure and asymmetry.
4.2.3 Schwingungsdämpfer
22,5°
• Monitoring of the maximum cycling rate.
Die Verdichter können starr montiert werden. Zur Ver-
15°
ringerung von Körperschall empfiehlt sich jedoch die
0°
For further information, see Technical Information
15°
Verwendung der speziell abgestimmten Schwingungs-
CT-110.
dämpfer.
22,5°
5.4.4 SE-E2
HINWEIS
!
!
Verdichter nicht starr auf Wärmeübertrager
Optional protection device for operation with frequency
montieren!
inverter and soft starter (for a ramp time shorter than
Beschädigungen des Wärmeübertragers mög-
22,5°
1 s).
lich (Schwingungsbrüche).
15°

• Dimensions and integration in the control identical to

0°

SE-E1.

Schwingungsdämpfer montieren
15°
22,5° • Suitable for all CS. compressors.
Die Schrauben anziehen, bis erste Verformungen der
oberen Gummischeibe sichtbar werden.
• Monitoring functions are basically identical to those
of SE-E1. However, the SE-E2 monitors phase fail-
ure during the entire running time of the compressor.
For further information, see Technical Information
ST-122.
5.4.5 Monitoring of the oil circuit
• For short circuits without liquid injection (LI) for addi-
tional cooling and for small system volume and small
refrigerant charge: Indirect monitoring with oil tem-
perature sensor (standard)
NOTICE
!
!
Lack of oil leads to a too high increase in tem-
perature.
Risk of damage to the compressor!
Verdichter
• For circuits with liquid injection (LI) for additional
CSK61, CS.65
cooling and / or for great system volume as well as
CS.75, CSH76
parallel compounding: Monitor oil level directly with
opto-electronic oil level monitoring (option), see
CS.85, CSH86
chapter Opto-electronic oil level monitoring OLC-D1-
CS.95, CSH96
S, page 26. The connection is on the compressor
CS.105
housing, see chapter Connections and dimensional
drawings, page 14, position 8.
Neigung in Quer-
richtung
dyna- statisch dyna-
misch misch
±7,5° ±15° ±22,5°
±17,5° ±15° ±22,5°
M
M
M10
M16
M16
M20
M20
25
43
43