D-Link DAP-600P User Manual

D-Link DAP-600P User Manual

Wireless ac2600 wave 2 mu-mimo dual band poe access point / router
Hide thumbs Also See for DAP-600P:
Table of Contents

Advertisement

User Manual
DAP-600P
Wireless AC2600 Wave 2 MU-MIMO Dual Band
PoE Access Point / Router
July 2020

Advertisement

Table of Contents
loading

Summary of Contents for D-Link DAP-600P

  • Page 1 User Manual DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router July 2020...
  • Page 2: Table Of Contents

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router User Manual Contents Chapter 1. Introduction.........5 Contents and Audience............5 Conventions..............5 Document Structure............5 Chapter 2. Overview..........6 General Information............6 Specifications..............8 Product Appearance............13 Upper Panel..............13 Back Panel...............14 Delivery Package............16 Chapter 3.
  • Page 3 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router User Manual Statistics..............73 Network Statistics............73 DHCP..............74 Clients and Session............75 Port Statistics............76 Multicast Groups............77 Routing Table............78 Connections Setup............79 LAN..............79 IPv4..............79 IPv6..............85 WAN..............89 Creating Dynamic IPv4 or Static IPv4 WAN Connection....91 Creating Dynamic IPv6 or Static IPv6 WAN Connection....95...
  • Page 4 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router User Manual System..............201 Configuration............202 Firmware Update............204 Local Update............205 Remote Update............206 Schedule..............207 Log..............211 Ping..............213 Traceroute..............215 Telnet/SSH..............217 System Time.............218 Auto Provision............220 Yandex.DNS..............222 Settings..............222 Devices and Rules............224 SkyDNS..............226 Settings..............227 Devices..............228 Chapter 5.
  • Page 5: Chapter 1. Introduction

    Chapter 2 gives an overview of the device's hardware and software features, describes its appearance and the package contents. Chapter 3 explains how to install the access point DAP-600P and configure a PC in order to access its web-based interface.
  • Page 6: Chapter 2. Overview

    In the access point mode, you are able to use DAP-600P to create a wireless network or to connect to a wired router. In the router mode, you are able to connect DAP-600P to a cable or DSL modem or to a private Ethernet line and use a high-speed Internet connection to successfully fulfill a wide range of professional tasks.
  • Page 7 Overview User Manual The “client” function is available in both modes and allows using DAP-600P as a wireless client and a wireless repeater in the access point mode and as a WISP repeater in the router mode. The SSH protocol support provides more secure remote configuration and management of the access point due to encryption of all transmitted traffic, including passwords.
  • Page 8: Specifications

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Overview User Manual Specifications Hardware Processor · MT7621AT (880MHz, dual core) · 128MB, DDR3 SDRAM Flash · 16MB, SPI Interfaces · 10/100/1000BASE-T WAN port with PoE support ·...
  • Page 9 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Overview User Manual Software Network functions · DHCP server/relay · Advanced configuration of built-in DHCP server · Stateful/Stateless mode for IPv6 address assignment, IPv6 prefix delegation ·...
  • Page 10 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Overview User Manual Wireless Module Parameters Standards · IEEE 802.11a/n/ac · IEEE 802.11b/g/n Frequency range · 2400 ~ 2483.5MHz · 5150 ~ 5350MHz The frequency range depends upon the ·...
  • Page 11 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Overview User Manual Wireless Module Parameters Transmitter output power · 802.11a (typical at room temperature 25 °C) 17dBm at 6, 54Mbps The maximum value of the transmitter ·...
  • Page 12 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Overview User Manual Wireless Module Parameters -62dBm at MCS6 -61dBm at MCS7 · Modulation schemes 802.11a: BPSK, QPSK, 16QAM, 64QAM with OFDM · 802.11b: DQPSK, DBPSK, DSSS, CCK ·...
  • Page 13: Product Appearance

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Overview User Manual Product Appearance Upper Panel Figure 1. Upper panel view. Mode Description The device is being loaded or the WLAN of both bands Solid red is off.
  • Page 14: Back Panel

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Overview User Manual Back Panel Figure 2. Back panel view. Port Description A button to restore the factory defaults. RESET To restore the factory defaults, push the button (with the device turned on), hold it for 10 seconds, and then release the button.
  • Page 15 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Overview User Manual Also, the power connector is located on the back panel of the access point. The device is equipped with four internal dual band Wi-Fi antennas.
  • Page 16: Delivery Package

    Wall mounting bracket with mounting kit • “Quick Installation Guide” (brochure). The “User Manual” and “Quick Installation Guide” documents are available on D-Link website (see www.dlink.ru). Using a power supply with different parameters than those indicated on the device will cause damage and void the warranty for this product.
  • Page 17: Chapter 3. Installation And Connection

    Computer or Mobile Device Configuration of the access point DAP-600P supporting the router mode (hereinafter referred to as “the access point”) is performed via the built-in web-based interface. The web-based interface is available from any operating system that supports a web browser.
  • Page 18: Connecting To Mobile Device With D-Link Assistant Application

    DAP- 600P. 5. In the settings of the wireless network DAP-600P (for operating in the 2.4GHz band) or DAP-600P-5G (for operating in the 5GHz band) on your mobile device, in the IP Settings field, select the Static value (for Android) or the Manual value (for iOS).
  • Page 19 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Installation and Connection User Manual 8. In the application menu, in the Connection method section select the Connection by IP address value. Figure 3. The Connection method section.
  • Page 20 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Installation and Connection User Manual 9. On the application main page click the CHANGE ADDRESS button. Figure 4. The application main page. Page 20 of 235...
  • Page 21 When DAP-600P is accessed with the application the next time and after, the authorization page opens. Enter the username (admin) and the password you specified.
  • Page 22: Connecting To Pc

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Installation and Connection User Manual Connecting to PC PC with Ethernet Adapter 1. Сonnect an Ethernet cable between the LAN port of the access point and the Ethernet port of your PC.
  • Page 23: Configuring Ip Address In Os Windows 7

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Installation and Connection User Manual Configuring IP Address in OS Windows 7 1. Click the Start button and proceed to the Control Panel window. 2. Select the Network and Sharing Center section. (If the Control Panel has the category...
  • Page 24 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Installation and Connection User Manual 3. In the menu located on the left part of the window, select the Change adapter settings line. Figure 7. The Network and Sharing Center window.
  • Page 25 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Installation and Connection User Manual 4. In the opened window, right-click the relevant Local Area Connection icon and select the Properties line in the menu displayed. Figure 8. The Network Connections window.
  • Page 26 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Installation and Connection User Manual 5. In the Local Area Connection Properties window, on the Networking tab, select the Internet Protocol Version 4 (TCP/IPv4) line. Click the Properties button.
  • Page 27 7. Click the OK button in the connection properties window. Now you can connect to the web-based interface of DAP-600P for configuring all needed parameters. To gain access to an external network (to the Internet), you also need to specify the default gateway and the addresses of DNS servers.
  • Page 28: Configuring Ip Address In Os Windows 10

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Installation and Connection User Manual Configuring IP Address in OS Windows 10 1. Click the Start button and proceed to the Settings window. 2. Select the Network & Internet section.
  • Page 29 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Installation and Connection User Manual 3. In the Change your network settings section, select the Change adapter options line. Figure 12. The Network & Internet window. Page 29 of 235...
  • Page 30 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Installation and Connection User Manual 4. In the opened window, right-click the relevant Local Area Connection icon and select the Properties line in the menu displayed. Figure 13. The Network Connections window.
  • Page 31 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Installation and Connection User Manual 5. In the Local Area Connection Properties window, on the Networking tab, select the Internet Protocol Version 4 (TCP/IPv4) line. Click the Properties button.
  • Page 32 7. Click the Close button in the connection properties window. Now you can connect to the web-based interface of DAP-600P for configuring all needed parameters. To gain access to an external network (to the Internet), you also need to specify the default gateway and the addresses of DNS servers.
  • Page 33: Pc With Wi-Fi Adapter

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Installation and Connection User Manual PC with Wi-Fi Adapter 1. For a switch supporting PoE: connect an Ethernet cable between the PoE-enabled switch and the WAN port of the access point.
  • Page 34: Configuring Wi-Fi Adapter In Os Windows 7

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Installation and Connection User Manual Configuring Wi-Fi Adapter in OS Windows 7 1. Click the Start button and proceed to the Control Panel window. 2. Select the Network and Sharing Center section. (If the Control Panel has the category...
  • Page 35 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Installation and Connection User Manual 5. In the Wireless Network Connection Properties window, on the Networking tab, select the Internet Protocol Version 4 (TCP/IPv4) line. Click the Properties button.
  • Page 36 11. Wait for about 20-30 seconds. After the connection is established, the network icon will be displayed as the signal level scale. Now you can connect to the web-based interface of DAP-600P for configuring all needed parameters. To gain access to an external network (to the Internet), you also need to specify the default gateway and the addresses of DNS servers.
  • Page 37: Configuring Wi-Fi Adapter In Os Windows 10

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Installation and Connection User Manual Configuring Wi-Fi Adapter in OS Windows 10 1. Click the Start button and proceed to the Settings window. 2. Select the Network & Internet section.
  • Page 38 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Installation and Connection User Manual 6. Select the Use the following IP address radio button and enter the value 192.168.0.51 in the IP address field. The Subnet mask field will be filled in automatically.
  • Page 39 User Manual 9. In the opened Wireless Network Connection window, select the wireless network DAP- 600P (for operating in the 2.4GHz band) or DAP-600P-5G (for operating in the 5GHz band) and click the Connect button. Figure 23. The list of available networks.
  • Page 40: Connecting To Web-Based Interface

    IP address of the access point (by default, the following IP address is specified: 192.168.0.50). Press the Enter key. Figure 25. Connecting to the web-based interface of the DAP-600P device. If the error “ The page cannot be displayed ” (or “ Unable to display the page ”/“ Could not connect to remote server ”) occurs upon connecting to the web-based interface of the access...
  • Page 41 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Installation and Connection User Manual If you configured the device previously, after access to the web-based interface the login page opens. Enter the username (admin) in the Username field and the password you specified in the Password field, then click the LOGIN button.
  • Page 42: Web-Based Interface Structure

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Installation and Connection User Manual Web-based Interface Structure The operating mode defines available sections and pages of the web-based interface. Summary Page On the Summary page, detailed information on the device state is displayed.
  • Page 43 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Installation and Connection User Manual The Device Information section displays the model and hardware version of the access point, the firmware version, and other data. To contact the technical support group (to send an e-mail), left-click the support e-mail address.
  • Page 44: Home Page

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Installation and Connection User Manual Home Page This page is available if the Router or WISP Repeater mode was selected in the Initial Configuration Wizard. The Home page displays links to the most frequently used pages with device's settings.
  • Page 45: Menu Sections

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Installation and Connection User Manual Menu Sections To configure the access point use the menu in the left part of the page. In the Initial Configuration section you can run the Initial Configuration Wizard. The Wizard...
  • Page 46: Notifications

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Installation and Connection User Manual Notifications The access point's web-based interface displays notifications in the top right part of the page. Figure 30. The web-based interface notifications.
  • Page 47: Configuring Via Web-Based Interface

    If you perform initial configuration of the access point via Wi-Fi connection, please make sure that you are connected to the wireless network of DAP-600P (see the WLAN name (SSID) on the barcode label on the bottom panel of the device) and click the NEXT button.
  • Page 48 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual On the opened page, click YES in order to leave the current language of the web-based interface or click NO to select the other language.
  • Page 49: Selecting Operation Mode

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Selecting Operation Mode Select the needed operation mode and click the NEXT button. Router In order to connect your device to a wired ISP, on the Device mode page, from the Connection method list, select the Autonomous value.
  • Page 50 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual In order to connect your device to a wireless ISP (WISP), on the Device mode page, from the Connection method list, select the Autonomous value. Then from the Work mode list, select the WISP Repeater value.
  • Page 51: Access Point Or Repeater

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Access Point or Repeater In order to connect your device to a wired router for adding a wireless network to the existing local network, on the Device mode page, from the Connection method list, select the Autonomous value.
  • Page 52 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual In order to connect your device to a wireless router for extending the range of the existing wireless network, on the Device mode page, from the Connection method list, select the Autonomous value.
  • Page 53: Mesh Network Main Device (Master)

    User Manual Mesh Network Main Device (Master) In order to configure DAP-600P as a main device of your Mesh network, from the Connection method list, select the Super Mesh value. Then from the Device Role list, select the Master value. From the Frequency band list, select the band where your Mesh network operates.
  • Page 54 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual In order to connect your main device to a wireless ISP (WISP), from the Work mode list, select the WISP Repeater value. In this mode you can connect your device to another access point, configure a WAN connection, set your own settings for the wireless network in the 2.4GHz and...
  • Page 55: Mesh Network Subordinate Device (Slave)

    User Manual Mesh Network Subordinate Device (Slave) In order to configure DAP-600P as a subordinate device of your Mesh network, from the Connection method list, select the Super Mesh value. Then from the Device Role list, select the Slave value. From the Frequency band list, select the band where your main device (in the Master role) operates.
  • Page 56: Changing Lan Ipv4 Address

    1. Select the Automatic obtainment of IPv4 address to let DAP-600P automatically obtain the LAN IPv4 address. If you want to manually assign the LAN IPv4 address for DAP-600P, do not select the Automatic obtainment of IPv4 address checkbox and fill in the IP address, Subnet mask, DNS IP address, Hostname fields and, if needed, the Gateway IP address field.
  • Page 57: Wi-Fi Client

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Wi-Fi Client This configuration step is available for the WISP Repeater and Repeater modes. 1. On the Wi-Fi Сlient page, click the WIRELESS NETWORKS button and select the network to which you want to connect in the opened window.
  • Page 58 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description The number of the key (from first to fourth) which will be used for Default key ID WEP encryption.
  • Page 59: Configuring Wan Connection

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Configuring WAN Connection This configuration step is available for the Router and WISP Repeater modes. You should configure your WAN connection in accordance with data provided by your Internet service provider (ISP).
  • Page 60: Static Ipv4 Connection

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Static IPv4 Connection Figure 45. The page for configuring Static IPv4 WAN connection. Fill in the following fields: IP address, Subnet mask, Gateway IP address, and DNS IP address.
  • Page 61: Static Ipv6 Connection

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Static IPv6 Connection Figure 46. The page for configuring Static IPv6 WAN connection. Fill in the following fields: IP address, Prefix, Gateway IP address, and DNS IP address.
  • Page 62: Pppoe, Ipv6 Pppoe, Pppoe Dual Stack, Pppoe + Dynamic Ip (Pppoe Dual Access) Connections

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual PPPoE, IPv6 PPPoE, PPPoE Dual Stack, PPPoE + Dynamic IP (PPPoE Dual Access) Connections Figure 47. The page for configuring PPPoE WAN connection.
  • Page 63: Pppoe + Static Ip (Pppoe Dual Access) Connection

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual PPPoE + Static IP (PPPoE Dual Access) Connection Figure 48. The page for configuring PPPoE + Static IP (PPPoE Dual Access) WAN connection.
  • Page 64: Pptp + Dynamic Ip Or L2Tp + Dynamic Ip Connection

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual PPTP + Dynamic IP or L2TP + Dynamic IP Connection Figure 49. The page for configuring PPTP + Dynamic IP WAN connection.
  • Page 65: Pptp + Static Ip Or L2Tp + Static Ip Connection

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual PPTP + Static IP or L2TP + Static IP Connection Figure 50. The page for configuring PPTP + Static IP WAN connection.
  • Page 66: Configuring Wireless Network

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Configuring Wireless Network This configuration step is available for the Router, Access point, WISP Repeater, and Repeater modes. 1. On the Wireless Network 2.4 GHz page, in the Network name field, specify your own name for the wireless network in the 2.4GHz band or leave the value suggested by the...
  • Page 67 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual 5. If you want to create an additional wireless network isolated from your LAN in the 2.4GHz band, select the Enable guest network checkbox (available for the Router and WISP Repeater modes only).
  • Page 68: Changing Web-Based Interface Password

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Changing Web-based Interface Password On this page, you should change the default administrator password. To do this, enter a new password in the Admin password and Password confirmation fields. You may set any password except admin.
  • Page 69 If problems of connection have not been solved, contact the technical support of your ISP (as a rule, the technical support phone is provided with the agreement) or the D-Link technical support (the phone number will be displayed on the page after several attempts of checking the connection).
  • Page 70: Connection Of Multimedia Devices

    DAP-600P in order to use these devices. Configuration of the LAN port is available only via Wi-Fi connection to DAP-600P . To start the Wizard, on the Home page, select the Connection of Multimedia Devices section.
  • Page 71 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual If you need to configure a connection via VLAN, click the ADVANCED MODE button. Figure 56. The Multimedia Devices Connection Wizard. The advanced mode.
  • Page 72 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual To deselect the LAN1 port in the simplified mode, left-click on it (the frame will disappear) and click the APPLY button.
  • Page 73: Statistics

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Statistics The pages of this section display data on the current state of the access point: • network statistics • IP addresses leased by the DHCP server •...
  • Page 74: Dhcp

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual DHCP The Statistics / DHCP page displays the information on computers that have been identified by hostnames and MAC addresses and have got IP addresses from the DHCP server of the device.
  • Page 75: Clients And Session

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Clients and Session On the Statistics / Clients and Session page, you can view the list of devices connected to the local network of the access point and information on current sessions of each device.
  • Page 76: Port Statistics

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Port Statistics On the Statistics / Port Statistics page, you can view statistics for traffic passing through ports of the access point. The information shown on the page can be used for diagnosing connection problems.
  • Page 77: Multicast Groups

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Multicast Groups The Statistics / Multicast Groups page displays addresses of active multicast groups (including IPTV channels and groups for transferring service information) to which the device is subscribed, and the interface through which the device is subscribed.
  • Page 78: Routing Table

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Routing Table This page is available if the Router or WISP Repeater mode was selected in the Initial Configuration Wizard. The Statistics / Routing Table page displays the information on routes. The table contains destination IP addresses, gateways, subnet masks, and other data.
  • Page 79: Connections Setup

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Connections Setup In this menu section you can configure basic parameters of the access point's local area network and connection to the Internet (create one or several WAN connections and define rules for their use).
  • Page 80 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description Local IP Address Available if the Access point or Repeater mode was selected in the Initial Configuration Wizard. Select the needed value from the drop-down list.
  • Page 81 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description Dynamic IP Addresses An operating mode of the access point's DHCP server. • Disable: The access point's DHCP server is disabled, clients' IP addresses are assigned manually.
  • Page 82 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description Available if the Router or WISP Repeater mode was selected in the Initial Configuration Wizard. Option 82 Circuit ID Option 82 Remote ID The value of the relevant field of DHCP option 82.
  • Page 83 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual To edit the parameters of an option, left-click the relevant line in the table. In the opened window, change the needed parameters and click the APPLY button.
  • Page 84 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual If needed, you can add your own address resource records. To do this, click the ADD button ( in the Hosts section (available if the Router or WISP Repeater mode was selected in the Initial Configuration Wizard).
  • Page 85: Ipv6

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual IPv6 Go to the IPv6 tab to change or add the IPv6 address of the access point, configure IPv6 addresses assignment settings, specify MAC address and IPv6 address pairs, or add own DNS records.
  • Page 86 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual In the Dynamic IPv6 Addresses section, you can configure IPv6 addresses assignment settings. Figure 72. Configuring the local interface. The IPv6 tab. The Dynamic IPv6 Addresses section.
  • Page 87 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual In the Static IP Addresses section, you can specify MAC address and IPv6 address pairs (set a fixed IPv6 address in the local area network for a device with a certain MAC address). The access...
  • Page 88 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual If needed, you can add your own address resource records. To do this, click the ADD button ( in the Hosts section (available if the Router or WISP Repeater mode was selected in the Initial Configuration Wizard).
  • Page 89: Wan

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual This page is available if the Router or WISP Repeater mode was selected in the Initial Configuration Wizard. On the Connections Setup / WAN page, you can create and edit connections used by the access point.
  • Page 90 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Figure 76. The Connections Setup / WAN page. The advanced mode. To create a new connection, click the ADD button ( ) in the Connections List section.
  • Page 91: Creating Dynamic Ipv4 Or Static Ipv4 Wan Connection

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Creating Dynamic IPv4 or Static IPv4 WAN Connection On the connection creation page, go to the All Settings tab. Then select the relevant value from the Connection type drop-down list and specify the needed values.
  • Page 92 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Figure 78. The page for creating a new Static IPv4 connection. The Ethernet section. Parameter Description Ethernet A MAC address assigned to the interface. This parameter is mandatory if your ISP uses MAC address binding.
  • Page 93 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Figure 79. The page for creating a new Static IPv4 connection. The IPv4 section. Parameter Description IPv4 For Static IPv4 type IP address Enter an IP address for this WAN connection.
  • Page 94 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Figure 80. The page for creating a new Static IPv4 connection. The Miscellaneous section. Parameter Description Miscellaneous If the switch is moved to the right, the network address translation function is enabled.
  • Page 95: Creating Dynamic Ipv6 Or Static Ipv6 Wan Connection

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Creating Dynamic IPv6 or Static IPv6 WAN Connection On the connection creation page, go to the All Settings tab. Then select the relevant value from the Connection type drop-down list and specify the needed values.
  • Page 96 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Figure 82. The page for creating a new Static IPv6 connection. The Ethernet section. Parameter Description Ethernet A MAC address assigned to the interface. This parameter is mandatory if your ISP uses MAC address binding.
  • Page 97 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Figure 83. The page for creating a new Static IPv6 connection. The IPv6 section. Parameter Description IPv6 For Static IPv6 type IPv6 address Enter an IPv6 address for this WAN connection.
  • Page 98 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description Primary IPv6 DNS Enter addresses of the primary and secondary IPv6 DNS servers in server/Secondary IPv6 the relevant fields.
  • Page 99: Creating Pppoe Wan Connection

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Creating PPPoE WAN Connection On the connection creation page, go to the All Settings tab. Then select the relevant value from the Connection type drop-down list and specify the needed values.
  • Page 100 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Figure 86. The page for creating a new PPPoE connection. The Ethernet section. Parameter Description Ethernet A MAC address assigned to the interface. This parameter is mandatory if your ISP uses MAC address binding.
  • Page 101 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Figure 87. The page for creating a new PPPoE connection. The PPP section. Parameter Description Move the switch to the right if you don't need to enter a username Without authorization and password to access the Internet.
  • Page 102 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description The maximum size of units transmitted by the interface. Authentication Select a required authentication method from the drop-down list or protocol leave the AUTO value.
  • Page 103 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Figure 88. The page for creating a new PPPoE connection. The Miscellaneous section. Parameter Description Miscellaneous If the switch is moved to the right, the network address translation function is enabled.
  • Page 104: Creating Pptp, L2Tp, Or L2Tp Over Ipsec Wan Connection

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Creating PPTP, L2TP, or L2TP over IPsec WAN Connection On the connection creation page, go to the All Settings tab. Then select the relevant value from the Connection type drop-down list and specify the needed values.
  • Page 105 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Figure 90. The page for creating a new PPTP connection. The PPP section. Parameter Description Move the switch to the right if you don't need to enter a username Without authorization and password to access the Internet.
  • Page 106 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description The maximum size of units transmitted by the interface. Select a required authentication method from the drop-down list or Authentication protocol leave the AUTO value.
  • Page 107 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Figure 91. The page for creating a new L2TP over IPsec connection. The IPsec section. Setting for both parties which establish the tunnel should be the same.
  • Page 108 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Figure 92. The page for creating a new PPTP connection. The Miscellaneous section. Parameter Description Miscellaneous If the switch is moved to the right, the network address translation function is enabled.
  • Page 109: Creating Pppoe Ipv6 Or Pppoe Dual Stack Wan Connection

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Creating PPPoE IPv6 or PPPoE Dual Stack WAN Connection On the connection creation page, go to the All Settings tab. Then select the relevant value from the Connection type drop-down list and specify the needed values.
  • Page 110 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Figure 94. The page for creating a new PPPoE IPv6 connection. The Ethernet section. Parameter Description Ethernet A MAC address assigned to the interface. This parameter is mandatory if your ISP uses MAC address binding.
  • Page 111 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Figure 95. The page for creating a new PPPoE IPv6 connection. The PPP section. Parameter Description Move the switch to the right if you don't need to enter a username Without authorization and password to access the Internet.
  • Page 112 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description The maximum size of units transmitted by the interface. Authentication Select a required authentication method from the drop-down list or protocol leave the AUTO value.
  • Page 113 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Figure 96. The page for creating a new PPPoE Pv6 connection. The IP section. Parameter Description Select a method for IPv6 address assignment from the drop-down Get IPv6 list or leave the Automatically value.
  • Page 114 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Figure 97. The page for creating a new PPPoE IPv6 connection. The Miscellaneous section. Parameter Description Miscellaneous For the PPPoE Dual Stack type only.
  • Page 115: Wan Reservation

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual WAN Reservation This page is available if the Router or WISP Repeater mode was selected in the Initial Configuration Wizard. On the Connections Setup / WAN Reservation page, you can enable the WAN backup function, which provides you with uninterrupted access to the Internet.
  • Page 116 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description A time period (in seconds) between regular checks of the main connection status. By default, the value 30 is specified. The value of this field should not be higher than product of Timeout check and Number of checks fields values.
  • Page 117: Wi-Fi

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Wi-Fi In this menu you can specify all needed settings for your wireless network. Basic Settings In the Wi-Fi / Basic Settings section, you can change basic parameters for the wireless interface of the access point and configure the basic and additional wireless networks.
  • Page 118 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual In the General Settings section, the following parameters are available: Parameter Description To enable Wi-Fi connection, move the switch to the right.
  • Page 119 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description Specify a period of time (in seconds) after which the access point Scanning period rescans channels. When you have configured the parameters, click the APPLY button.
  • Page 120 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description Wi-Fi Network A name for the wireless network. The name can consist of digits and Network name (SSID) Latin characters.
  • Page 121 Parameter Description If the wireless network broadcasting is disabled, devices cannot connect to the wireless network. Upon that DAP-600P can connect to another access point as a wireless client. To enable/disable broadcasting on a schedule, click the Set schedule button ( ).
  • Page 122 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual In the Security Settings section, you can change security settings of the wireless network. By default, the WPA2-PSK network authentication type of both bands of the wireless network is specified.
  • Page 123 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual The WPA , WPA2 , and WPA/WPA2 mixed authentication types require a RADIUS server. When the Open or WEP value is selected, the following settings are displayed on the page (unavailable for the wireless network operating modes which support the standard 802.11n or...
  • Page 124 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description For Open authentication type only. To activate WEP encryption, move the switch to the right. Upon that Enable encryption WEP...
  • Page 125 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual When the WPA-PSK, WPA2-PSK, or WPA-PSK/WPA2-PSK mixed value is selected, the following fields are displayed on the page: Figure 103. The WPA2-PSK value is selected from the Network authentication drop-down list.
  • Page 126 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual When the WPA, WPA2, or WPA/WPA2 mixed value is selected, the following settings are displayed on the page: Figure 104. The WPA2 value is selected from the Network authentication drop-down list.
  • Page 127: Client Management

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Client Management On the Wi-Fi / Client Management page, you can view the list of wireless clients connected to the access point.
  • Page 128: Wps

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual On the Wi-Fi / WPS page, you can enable the function for configuration of the WLAN and select a method for connection to the WLAN.
  • Page 129 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual When the WPS function is enabled, the Information section is available on the page. Parameter Description The state of the WPS function: •...
  • Page 130: Using Wps Function Via Web-Based Interface

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Using WPS Function via Web-based Interface To connect to the basic wireless network via the PIN method of the WPS function, follow the next steps: 1.
  • Page 131: Wmm

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual On the Wi-Fi / WMM page, you can enable the Wi-Fi Multimedia function. The WMM function implements the QoS features for Wi-Fi networks. It helps to improve the quality of data transfer over Wi-Fi networks by prioritizing different types of traffic.
  • Page 132 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual The WMM function allows assigning priorities for four Access Categories (AC): • BK (Background), low priority traffic (print jobs, file downloads, etc.).
  • Page 133 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description Transmission Opportunity. The higher the value, the higher is the TXOP Access Category priority. Admission Control Mandatory. If the switch is moved to the right, the device cannot use the relevant Access Category.
  • Page 134: Client

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Client On the Wi-Fi / Client page, you can configure the device as a client to connect to a wireless access point or to a WISP.
  • Page 135 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual In the Wireless Networks section, the list of available wireless networks is displayed. To view the latest data on available wireless networks, click the UPDATE LIST button.
  • Page 136 An encryption method: TKIP, AES, or TKIP+AES. When you have configured the parameters, click the APPLY button. When connecting to a wireless access point, the wireless channel of DAP-600P will switch to the channel of the access point to which you have connected.
  • Page 137: Additional

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Additional On page of the Wi-Fi / Additional section, you can define additional parameters for the WLAN of the access point. To configure the 2.4GHz band or 5GHz band, go to the relevant tab.
  • Page 138 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual The following fields are available on the page: Parameter Description The channel bandwidth for 802.11n standard in the 2.4GHz band (the 2.4 GHz tab).
  • Page 139 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description The STBC (Space-time block coding) technique allows increasing data transfer reliability even for portable devices equipped with poor antennas (smartphones, pads, etc.) due to using several data streams STBC and processing several versions or received data.
  • Page 140 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description The number of beacon frames between sending DTIM messages DTIM period (messages notifying on broadcast or multicast transmission). The time interval (in seconds) between keep alive checks of wireless devices from your WLAN.
  • Page 141: Mac Filter

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual MAC Filter On the Wi-Fi / MAC Filter page, you can define a set of MAC addresses of devices which will be allowed to access the WLAN, or define MAC addresses of devices which will not be allowed to access the WLAN.
  • Page 142 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual You can specify the following parameters: Parameter Description Frequency band From the drop-down list, select a band of the wireless network.
  • Page 143 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual To change or delete the schedule for a rule, click the Select schedule button ( ) in the line corresponding to this rule. In the opened window, change the parameters and click the SAVE button or click the DELETE FROM SCHEDULE button.
  • Page 144: Super Mesh

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Super Mesh On the Wi-Fi / Super Mesh page, you can enable the Super Mesh function. This function is designed to quickly connect multiple devices into one transport network for providing high-quality Wi-Fi coverage in living units of complicated planning or for creating a large temporary Wi-Fi network for an outdoor event.
  • Page 145 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Figure 114. The Wi-Fi / Super Mesh page. To activate the Super Mesh function, on the tab of the relevant band, move the Enable Super Mesh switch to the right.
  • Page 146 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description A name of the Mesh network. This value should be the same for all devices of your Mesh network.
  • Page 147 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description The identifier which shows that a device belongs to the Mesh Domain network. The IPv4 and/or IPv6 address of a device.
  • Page 148 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description The short name for the Mesh network device which MAC address is displayed in the Neighbour MAC Address field.
  • Page 149: Roaming

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Roaming On the Wi-Fi / Roaming page, you can enable the function of smart adjustment of Wi-Fi clients. This function is designed for wireless networks based on several access points or routers. If the function is enabled for all access points (routers) which establish a wireless network, then wireless clients will always connect to the device with the highest signal level.
  • Page 150 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description Move the switch to the right in order to use multicast traffic for service data exchange between access points (routers). This setting is needed if the devices which support the smart adjustment function are located in different subnets.
  • Page 151: Advanced

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Advanced In this menu you can configure advanced settings of the access point: • add name servers • configure autonegotiation or manually configure speed and duplex mode for each Ethernet port of the access point •...
  • Page 152: Dns

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual On the Advanced / DNS page, you can add DNS servers to the system. Figure 116. The Advanced / DNS page.
  • Page 153 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Specify needed settings for IPv4 in the DNS IPv4 section and for IPv6 in the DNS IPv6 section. If you want to configure automatic obtainment of DNS servers addresses, move the Manual switch to the left.
  • Page 154: Ports Settings

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Ports Settings On the Advanced / Ports Settings page, you can configure or disable autonegotiation of speed and duplex mode or manually configure speed and duplex mode for each Ethernet port of the access point.
  • Page 155 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Figure 118. The window for changing the settings of the access point's port. In the opened window, specify the needed parameters:...
  • Page 156 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description Autonegotiation Modes To enable the needed data transfer modes, move relevant switches to the right. Flow control Move the switch to the right to enable the flow control function for the port.
  • Page 157: Mac Filter

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual MAC Filter On the Advanced / MAC Filter page, you can configure MAC-address-based filtering for computers of the access point's LAN. This page is also available in the Firewall section if the Router or WISP Repeater mode was selected in the Initial Configuration Wizard.
  • Page 158 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual In the opened window, you can specify the following parameters: Parameter Description Move the switch to the right to enable the rule.
  • Page 159: Vlan

    LAN line. On the opened page, from the Type drop-down list of the element corresponding to the relevant LAN port or Wi-Fi network, select the Excluded value and click the APPLY button. Configuration of the LAN port is available only via Wi-Fi connection to DAP-600P . Page 159 of 235...
  • Page 160 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual To create a new VLAN, click the ADD button ( Figure 122. The page for adding a VLAN. You can specify the following parameters:...
  • Page 161 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description Select the Untagged value for each Wi-Fi interface included in the VLAN. Wireless interfaces Leave the Excluded value for the Wi-Fi interfaces not included in the VLAN.
  • Page 162: Snmp

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual SNMP This page is available if the Router or WISP Repeater mode was selected in the Initial Configuration Wizard. On the Advanced / SNMP page, you can enable and configure the SNMP agent of the access point.
  • Page 163 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual In order to enable the SNMP agent, in the Configuration section, move the Enable SNMP switch to the right. Then specify the needed parameters.
  • Page 164 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual If the SNMP manager operates over SNMPv3, create a read-only user which will be used by the SNMP manager to get data on the device. To do this, in the Users section, click the ADD button Figure 124.
  • Page 165 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Click the SAVE button. To edit a user, select the relevant line in the table. In the opened window, change the needed values and click the SAVE button.
  • Page 166: Ddns

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual DDNS This page is available if the Router or WISP Repeater mode was selected in the Initial Configuration Wizard. On the Advanced / DDNS page, you can configure the access point to use one or several DDNS services.
  • Page 167 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual On the opened page, you can specify the following parameters: Parameter Description Enter the full domain name registered at your DDNS provider.
  • Page 168: Redirect

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Redirect This page is available if the Router or WISP Repeater mode was selected in the Initial Configuration Wizard. On the Advanced / Redirect page, you can enable notifications on the reason of the Internet connection failure.
  • Page 169: Routing

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Routing This page is available if the Router or WISP Repeater mode was selected in the Initial Configuration Wizard. On the Advanced / Routing page, you can specify static (fixed) routes.
  • Page 170 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual In the opened window, you can specify the following parameters: Parameter Description Move the switch to the right to enable the route.
  • Page 171: Tr-069 Client

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual TR-069 Client This page is available if the Router or WISP Repeater mode was selected in the Initial Configuration Wizard. On the Advanced / TR-069 Client page, you can configure the access point for communication with a remote Auto Configuration Server (ACS).
  • Page 172 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description Inform Settings Move the switch to the right so the access point may send reports (data on the device and network statistics) to the ACS.
  • Page 173: Remote Access

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Remote Access This page is available if the Router or WISP Repeater mode was selected in the Initial Configuration Wizard. On the Advanced / Remote Access page, you can configure access to the web-based interface of the access point.
  • Page 174 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual In the opened window, you can specify the following parameters: Parameter Description An IP version to which the rule will be applied. Select the relevant IP version value from the drop-down list.
  • Page 175: Upnp Igd

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual UPnP IGD This page is available if the Router or WISP Repeater mode was selected in the Initial Configuration Wizard. On the Advanced / UPnP IGD page, you can enable the UPnP IGD protocol. The access point uses the UPnP IGD protocol for automatic configuration of its parameters for network applications requiring an incoming connection to the access point.
  • Page 176: Udpxy

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual UDPXY This page is available if the Router or WISP Repeater mode was selected in the Initial Configuration Wizard. On the Advanced / UDPXY page, you can allow the access point to use the built-in UDPXY application.
  • Page 177 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual After specifying the needed parameters, click the APPLY button. To access the status page of the application, click the Status link.
  • Page 178: Igmp

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual IGMP This page is available if the Router or WISP Repeater mode was selected in the Initial Configuration Wizard. On the Advanced / IGMP page, you can allow the access point to use IGMP.
  • Page 179: Alg/Passthrough

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual ALG/Passthrough This page is available if the Router or WISP Repeater mode was selected in the Initial Configuration Wizard. On the Advanced / ALG/Passthrough page, you can allow the access point to use RTSP, enable the SIP ALG and PPPoE/PPTP/L2TP/IPsec pass through functions.
  • Page 180 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual The following elements are available on the page: Parameter Description Move the switch to the right to enable SIP. Such a setting allows using the SIP ALG function.
  • Page 181: Ipsec

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual IPsec This page is available if the Router or WISP Repeater mode was selected in the Initial Configuration Wizard. On the Advanced / IPsec page, you can configure VPN tunnels based on IPsec protocol.
  • Page 182 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual To create a new tunnel, click the ADD button ( ) in the Tunnels section. Setting for both devices which establish the tunnel should be the same.
  • Page 183 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description Select an identification method for the remote host (router) from the drop-down list: • Address: The remote host is identified by its IP address.
  • Page 184 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description An operation mode of the IPsec tunnel. Select a value from the drop- down list. • TUNNEL: As a rule, it is used to create a secure connection to remote networks.
  • Page 185 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Figure 140. The page for adding an IPsec tunnel. The First Phase / The Second Phase sections. Parameter Description The First Phase Encryption mode Select an encryption mode from the drop-down list.
  • Page 186 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description The lifetime of IKE-SA keys in seconds. After the specified period it is required to renegotiate the keys. The value specified in this field...
  • Page 187 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description The lifetime of Phase 2 keys in seconds. After the specified period it is IPsec-SA lifetime required to renegotiate the keys. The value specified in this field should be greater than zero.
  • Page 188 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual To edit the parameters of an existing tunnel, in the Tunnels section, select the relevant tunnel in the table. On the opened page, change the needed parameters and click the APPLY button.
  • Page 189: Firewall

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Firewall This section is available if the Router or WISP Repeater mode was selected in the Initial Configuration Wizard. In this menu you can configure the firewall of the access point: •...
  • Page 190 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Figure 143. The page for adding a rule for IP filtering. You can specify the following parameters: Parameter Description General Settings Move the switch to the right to enable the rule.
  • Page 191 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description Select an action for the rule. • Allow: Allows packet transmission in accordance with the Action criteria specified by the rule.
  • Page 192 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description The destination host start IPv4 or IPv6 address. If it is necessary to specify a single address, leave the End IPv4 Start IPv4 address / address / End IPv6 address field blank.
  • Page 193 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual To remove a rule, select the checkbox located to the left of the relevant line of the table and click the DELETE button ( ).
  • Page 194: Virtual Servers

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Virtual Servers On the Firewall / Virtual Servers page, you can create virtual servers for redirecting incoming Internet traffic to a specified IP address in the local area network.
  • Page 195 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Figure 145. The page for adding a virtual server. You can specify the following parameters: Parameter Description General Settings Move the switch to the right to enable the server.
  • Page 196 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description Move the switch to the right in order to let the users of the access point's LAN access the local server using the external IP address of...
  • Page 197: Dmz

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual A DMZ is a host or network segment located “between” internal (local) and external (global) networks. In the device, the DMZ implements the capability to transfer a request coming to a port of the access point from the external network to a specified host of the internal network.
  • Page 198: Url Filter

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual URL Filter On the Firewall / URL Filter page, you can specify restrictions on access to certain web sites. Figure 147. The Firewall / URL Filter page.
  • Page 199 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual To specify URL addresses to which the selected filtering mode will be applied, in the Addresses section, click the ADD button ( ).
  • Page 200 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual To enable the URL filter for the time specified in the schedule and disable it at the other time, select the Enable value from the Action for rule upon activation of schedule drop-down list and click the SAVE button.
  • Page 201: System

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual System In this menu you can do the following: • change the password used to access the access point's settings •...
  • Page 202: Configuration

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Configuration On the System / Configuration page, you can change the password for the administrator account used to access the web-based interface of the access point and to access the device settings via...
  • Page 203 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual The following buttons are also available on the page: Control Description Click the button to restore the factory default settings. Also you can...
  • Page 204: Firmware Update

    (in seconds) between checks or leave the value specified by default (43200). By default, in the Remote server URL field, the D-Link update server address (fwupdate.dlink.ru) is specified. To add one more address, click the ADD button and enter the address in the displayed line.
  • Page 205: Local Update

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Local Update Attention! Do not turn off the access point before the firmware update is completed. This may cause the device breakdown.
  • Page 206: Remote Update

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Remote Update Attention! Do not turn off the access point before the firmware update is completed. This may cause the device breakdown.
  • Page 207: Schedule

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Schedule On the System / Schedule page, you can enable/disable Wi-Fi connection and configure automatic reboot of the device on a schedule, and set a schedule for different filter rules.
  • Page 208 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual In the opened window, in the System Time field, the system time of the device is displayed. You can select the Simplified mode choice of the radio button and specify the following parameters:...
  • Page 209 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual To set a schedule for a task which will be applied to a filter rule or will enable/disable Wi-Fi connection, click the ADD button ( ) in the All Tasks section.
  • Page 210 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description Simplified mode Specify the time period for performing a task. • Every minute. • Every hour: When this value is selected, the Time field is displayed in the section.
  • Page 211: Log

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual On the System / Log page, you can set the system log options and configure sending the system log to a remote host.
  • Page 212 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description The IP or URL address of the host from the local or global network, Server to which the system log will be sent.
  • Page 213: Ping

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Ping On the System / Ping page, you can check availability of a host from the local or global network via the Ping utility.
  • Page 214 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Figure 156. The System / Ping page. The additional settings window. In the opened window, in the Packet size field, specify the volume of data sent in a request. In the Time to wait for a response field, specify the response waiting period in seconds.
  • Page 215: Traceroute

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Traceroute On the System / Traceroute page, you can determine the route of data transfer to a host via the traceroute utility.
  • Page 216 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual To specify additional settings, click the MORE SETTINGS button. Figure 158. The System / Traceroute page. The additional settings window. In the opened window, you can specify the following parameters:...
  • Page 217: Telnet/Ssh

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Telnet/SSH On the System / Telnet/SSH page, you can enable or disable access to the device settings via TELNET and/or SSH from your LAN. By default, access is disabled.
  • Page 218: System Time

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual System Time On the System / System Time page, you can manually set the time and date of the access point or configure automatic synchronization of the system time with a time server on the Internet.
  • Page 219 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual 4. Click the APPLY button. The System date and System time fields will be filled in automatically. In some cases NTP servers addresses are provided by your ISP. In this case, you need to move the Get NTP server addresses using DHCP switch to the right and click the APPLY button.
  • Page 220: Auto Provision

    On the System / Auto Provision page, you can enable the Auto Provision function. The Auto Provision function allows your ISP to manage the device’s settings remotely: DAP-600P connects to the ISP’s server, compares the current configuration file with the configuration file stored on this server, and updates its settings if the files are different.
  • Page 221 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Parameter Description If the switch is moved to the right, the parameters of your ISP's server (the address, the location of the configuration file, and the protocol) are automatically specified using DHCP options 66 and 67.
  • Page 222: Yandex.dns

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Yandex.DNS This section is available if the Router or WISP Repeater mode was selected in the Initial Configuration Wizard. This menu is designed to configure the Yandex.DNS service.
  • Page 223 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual When the service is enabled, the Default Mode section is displayed on the page. Select the needed choice of the radio button to configure filtering for all devices of the access point's network: •...
  • Page 224: Devices And Rules

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Devices and Rules On the Yandex.DNS / Devices and Rules page, you can specify a filtering mode for each device separately.
  • Page 225 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual In the opened window, you can specify the following parameters: Parameter Description The MAC address of a device from the access point's LAN. You can...
  • Page 226: Skydns

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual SkyDNS This section is available if the Router or WISP Repeater mode was selected in the Initial Configuration Wizard. This menu is designed to configure the SkyDNS service.
  • Page 227: Settings

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual Settings On the SkyDNS / Settings page, you can enable the SkyDNS service and specify settings for its operation. The SkyDNS service is unavailable when the Yandex.DNS service is enabled.
  • Page 228: Devices

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual The default filtering profile will be applied to all devices newly connected to the access point's network. To change the parameters of your account on the SkyDNS service web site, click the Go to personal profile page link.
  • Page 229 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Configuring via Web-based Interface User Manual To assign a specific filtering profile for a device, click the ADD button ( ) in the Device List section or left-click the name of the filtering profile in the line of the device for which a profile should be assigned in the Known Clients section.
  • Page 230: Operation Guidelines

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Operation Guidelines User Manual CHAPTER 5. OPERATION GUIDELINES Safety Rules and Conditions Please carefully read this section before installation and connection of the device. Make sure that the device is not damaged.
  • Page 231: Wireless Installation Considerations

    RF noise in your home or office. To maximize your wireless range, follow the guidelines below. 1. Keep the number of walls and ceilings between the DAP-600P device and other network devices to a minimum – each wall or ceiling can reduce your wireless network range by 3- 90 feet (1-30 meters).
  • Page 232: Abbreviations And Acronyms

    DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Abbreviations and Acronyms User Manual CHAPTER 6. ABBREVIATIONS AND ACRONYMS Access Category Advanced Encryption Standard Access Point Address Resolution Protocol BPSK Binary Phase-shift Keying BSSID Basic Service Set Identifier...
  • Page 233 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Abbreviations and Acronyms User Manual IGMP Internet Group Management Protocol Internet Key Exchange Internet Protocol IPTV Internet Protocol Television IPsec Internet Protocol Security Internet Service Provider L2TP...
  • Page 234 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Abbreviations and Acronyms User Manual pppd Point-to-Point Protocol Daemon PPPoE Point-to-point protocol over Ethernet PPTP Point-to-point tunneling protocol Pre-shared key Quadrature Amplitude Modulation Quality of Service QPSK...
  • Page 235 DAP-600P Wireless AC2600 Wave 2 MU-MIMO Dual Band PoE Access Point / Router Abbreviations and Acronyms User Manual Wired Equivalent Privacy Wi-Fi Wireless Fidelity WISP Wireless Internet Service Provider WLAN Wireless Local Area Network Wi-Fi Multimedia Wi-Fi Protected Access Wi-Fi Protected Setup...

Table of Contents