Warning Messages - Yamaha DSP5D Owner's Manual

Warning Messages

These are messages displayed in the lower part of the screen. They will disappear after a certain duration has elapsed.
Message
#xxx of Scene is Empty!
#xxx of Scene is Read Only!
#xxx of Scene is Protected!
Cannot Undo!
Cannot Assign!
Cannot Drop!
Pair Made.
Pair Broken.
EFFECT CUE: Turned Off.
KEY IN CUE: Turned Off.
Overwrite Existing Event.
Event List Full! Last Event cancelled.
Interval from Previous Event is Too Short!
TIME CODE: Frame Jump!
TIME CODE: Frame Mismatch!
MIDI: Data Framing Error!
MIDI: Data Overrun!
MIDI: Rx Buffer Full!
MIDI: Tx Buffer Full!
USB: Data Framing Error!
USB: Data Overrun!
USB: Rx Buffer Full!
USB: Tx Buffer Full!
SLOT x: Data Framing Error!
SLOT x: Data Overrun!
SLOT x: Rx Buffer Full!
SLOT x: Tx Buffer Full!
RS422: Data Framing Error!
RS422: Data Overrun!
RS422: Rx Buffer Full!
RS422: Tx Buffer Full!
CASCADE: Data Framing Error!
CASCADE: Data Overrun!
CASCADE: Rx Buffer Full!
CASCADE: Tx Buffer Full!
DME Control: Data Framing Error!
DME Control: Data Overrun!
DME Control: Rx Buffer Full!
DME Control: Tx Buffer Full!
Wrong Word Clock!
Sync Error! [xxxx]
xxxx No Signal Present!
Data Type Conflict! Canceled.
HA Type Conflict! Data Ignored.
Conflicting GPI OUT Cancelled.
Conflicting USER DEFINED KEY
Cancelled.
Conflicting FADER START Cancelled.
Wrong Password!
System Password Changed.
Console Password Changed.
No data has been stored in the scene you attempted to recall, or the data has been damaged so that it
cannot be recalled.
You attempted to overwrite (store) a read-only scene.
You attempted to overwrite (store) a protected scene.
You pressed the SCENE MEMORY [UNDO] key when Undo was not available.
You clicked an unavailable (grayed-out) grid in the patch screen, or pressed an invalid key on the panel
(e.g., a DCA/MUTE assign key that is unavailable due to the selected channel).
You attempted to drop a EQ/compressor/gate/EQ/effect mini-graph onto a location of a different type.
You used a panel operation to assign channel pairing.
You used a panel operation to cancel channel pairing.
CUE was defeated because you switched to another screen from the EQ PARAM or EFFECT ASSIGN
screen, or because you switched the selected effect.
KEY IN CUE was defeated because you switched from the GATE PRM/COMP PRM screen to a different
screen.
In the EVENT LIST screen you input an event at the same time as a previously-input event, so the exist-
ing event was overwritten.
In the EVENT LIST screen, the event list is full; the last event in the event list was pushed out and deleted
when you added a new event.
The event you are attempting to input in the EVENT LIST screen is too close to an existing event earlier
than that location, so it is possible that it may not be recalled at the time you intend.
The time code that was input in the EVENT LIST screen has experienced a frame jump or is running
backward.
The incoming time code has a frame rate that is different than the time code specified in the EVENT LIST
screen.
Invalid signals are being input to the MIDI IN connector.
Invalid signals are being input to the MIDI IN connector.
Too much data is being received at the MIDI IN connector.
Too much data is being sent from the MIDI OUT connector.
Invalid signals are being input from the USB connector input port.
Invalid signals are being input from the USB connector input port.
Too much data is being received at the USB connector input port.
Too much data is being sent from the USB connector output port.
Invalid signals are being input from the SLOT x input port.
Invalid signals are being input from the SLOT x input port.
Too much data is being received at the SLOT x input port.
Too much data is being sent from the SLOT x output port.
Invalid signals are being received at the HA REMOTE connector or RS422 REMOTE connector.
Invalid signals are being received at the HA REMOTE connector or RS422 REMOTE connector.
Too much data is being received at the HA REMOTE connector or RS422 REMOTE connector.
Too much data is being transmitted from the HA REMOTE connector or RS422 REMOTE connector.
Invalid signals are being input to the CASCADE IN/OUT connector.
Invalid signals are being input to the CASCADE IN/OUT connector.
Too much data is being received at the CASCADE IN/OUT connector.
Too much data is being transmitted from the CASCADE IN/OUT connector.
Invalid signals are being input during communication with the DME.
Invalid signals are being input during communication with the DME.
Too much data is being received during communication with the DME.
Too much data is being transmitted during communication with the DME.
The PM5D cannot synchronize because the source selected by MASTER CLOCK SELECT in the WORD
CLOCK screen is not appropriate.
The xxxx signal is not synchronized with the PM5D.
The xxxx signal is not being input.
You attempted to execute a library recall or channel copy operation on a different type of channel.
You attempted to recall a HA library of a different model (PM5D model or PM5D-RH model).
The parameter you assigned to the FADER START function or to a User Defined key is the same as an
existing GPI OUT assignment, so the GPI OUT assignment was cancelled.
The parameter you assigned to GPI OUT is the same as an existing User Defined key assignment, so the
User Defined key assignment was cancelled.
The parameter you assigned to GPI OUT is the same as an existing FADER START function, so the FADER
START assignment was cancelled.
The system password or console password you input was incorrect.
The system password has been changed.
The console password has been changed.
PM5D/PM5D-RH V2 / DSP5D Owner's Manual
Meaning
Reference section
377