Yamaha DSP5D Owner's Manual page 331

❏ REV→PAN
One input, two output reverb and autopan effects in
parallel.
Parameter Range
REV TIME 0.3–99.0 s Reverb time
INI. DLY 0.0–500.0 ms Initial delay before reverb begins
HI. RATIO 0.1–1.0 High-frequency reverb time ratio
DIFF. 0–10 Spread
DENSITY 0–100% Reverb density
THRU, 21.2 Hz–
HPF High-pass filter cutoff frequency
8.00 kHz
50.0 Hz–16.0 kHz,
LPF Low-pass filter cutoff frequency
THRU
Reverb and panned reverb bal-
REV.BAL 0–100% ance (0% = all panned reverb,
100% = all reverb)
FREQ. 0.05–40.00 Hz Modulation speed
DEPTH 0–100% Modulation depth
*1
DIR. Panning direction
WAVE Sine, Tri, Square Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
Used in conjunction with TEMPO
*2
NOTE
to determine FREQ.
*1. L↔R, L→R, L←R, Turn L, Turn R
*2.
❏ DELAY+ER.
One input, two output delay and early reflections effects in
parallel.
Parameter Range
DELAY L 0.0–1000.0 ms Left channel delay time
DELAY R 0.0–1000.0 ms Right channel delay time
FB. DLY 0.0–1000.0 ms Feedback delay time
Feedback gain (plus values for
FB. GAIN –99 to +99% normal-phase feedback, minus
values for reverse-phase feedback)
HI. RATIO 0.1–1.0 High-frequency feedback ratio
THRU, 21.2 Hz–
HPF High-pass filter cutoff frequency
8.00 kHz
50.0 Hz–16.0 kHz,
LPF Low-pass filter cutoff frequency
THRU
Delay and early reflections bal-
DLY/ER 0–100% ance (0% = all delay, 100% = all
early reflections)
S-Hall, L-Hall, Ran-
TYPE dom, Revers, Plate, Type of early reflection simulation
Spring
ROOMSIZE 0.1–20.0 Reflection spacing
Early reflections decay characteris-
LIVENESS 0–10
tics (0 = dead, 10 = live)
INI. DLY 0.0–500.0 ms Initial delay before reverb begins
DIFF. 0–10 Spread
DENSITY 0–100% Reverb density
ER NUM. 1–19 Number of early reflections
SYNC OFF/ON Tempo parameter sync on/off
Used in conjunction with TEMPO
*1
NOTE L
to determine left channel DELAY L
Used in conjunction with TEMPO
NOTE R 1 to determine right channel DELAY
R
Used in conjunction with TEMPO
NOTE FB 1
to determine FB. DLY
*1.
(Maximum value depends on the tempo setting)
❏ DELAY→ER.
One input, two output delay and early reflections effects in
series.
Description Parameter
DELAY L
DELAY R
FB. DLY
FB. GAIN
HI. RATIO
HPF
LPF
DLY.BAL
TYPE
ROOMSIZE 0.1–20.0
LIVENESS
INI. DLY
DIFF.
DENSITY
ER NUM.
SYNC
NOTE L
Description
NOTE R
NOTE FB
*1.
❏ DELAY+REV
One input, two output delay and reverb effects in parallel.
Parameter
DELAY L
DELAY R
FB. DLY
FB. GAIN
DELAY HI
HPF
LPF
DLY/REV
REV TIME
INI. DLY
REV HI
DIFF.
DENSITY
SYNC
NOTE L
NOTE R
NOTE FB
*1.
PM5D/PM5D-RH V2 / DSP5D Owner's Manual
Range
0.0–1000.0 ms Left channel delay time
0.0–1000.0 ms Right channel delay time
0.0–1000.0 ms Feedback delay time
Feedback gain (plus values for
–99 to +99% normal-phase feedback, minus
values for reverse-phase feedback)
0.1–1.0 High-frequency feedback ratio
THRU, 21.2 Hz–
High-pass filter cutoff frequency
8.00 kHz
50.0 Hz–16.0 kHz,
Low-pass filter cutoff frequency
THRU
Delay and early reflected delay
0–100% balance (0% = all early reflected
delay, 100% = all delay)
S-Hall, L-Hall, Ran-
dom, Revers, Plate, Type of early reflection simulation
Spring
Reflection spacing
Early reflections decay characteris-
0–10
tics (0 = dead, 10 = live)
0.0–500.0 ms Initial delay before reverb begins
0–10 Spread
0–100% Reverb density
1–19 Number of early reflections
OFF/ON Tempo parameter sync on/off
Used in conjunction with TEMPO
*1
to determine left channel DELAY L
Used in conjunction with TEMPO
1 to determine right channel DELAY
R
Used in conjunction with TEMPO
1
to determine FB. DLY
(Maximum value depends on the tempo setting)
Range
0.0–1000.0 ms Left channel delay time
0.0–1000.0 ms Right channel delay time
0.0–1000.0 ms Feedback delay time
Feedback gain (plus values for
–99 to +99% normal-phase feedback, minus
values for reverse-phase feedback)
Delay high-frequency feedback
0.1–1.0
ratio
THRU, 21.2 Hz–
High-pass filter cutoff frequency
8.00 kHz
50.0 Hz–16.0 kHz,
Low-pass filter cutoff frequency
THRU
Delay and reverb balance (0% =
0–100%
all delay, 100% = all reverb)
0.3–99.0 s Reverb time
0.0–500.0 ms Initial delay before reverb begins
0.1–1.0 High-frequency reverb time ratio
0–10 Spread
0–100% Reverb density
OFF/ON Tempo parameter sync on/off
Used in conjunction with TEMPO
*1
to determine left channel DELAY L
Used in conjunction with TEMPO
1 to determine right channel DELAY
R
Used in conjunction with TEMPO
1
to determine FB. DLY
(Maximum value depends on the tempo setting)
Reference section
Description
Description
331