Yamaha DSP5D Owner's Manual page 265

Digital mixing console/digital mixing system
Hide thumbs Also See for DSP5D:
Table of Contents

Advertisement

❏ When the MTRX from MIX button is on
You can view the status of the signals sent from all MIX
channels or STEREO A/B channels to a specific
MATRIX bus.
B SEND LEVEL/SEND POINT
Select one of the following two parameters to view in
the grid.
❏ When the SEND LEVEL button is on
The send levels sent from the MIX channels or STE-
REO A/B channels to the MATRIX buses will be shown
as a bar graph in each grid. Channels for which the sig-
nal sent to the MATRIX bus is turned off are shown by
gray bars, and channels for which the signal is turned
on are shown by blue bars.
Channels for which the
signal sent to the MATRIX
bus is turned off (gray bar
graph)
To edit the send level, move the cursor to the grid
where the MIX or STEREO A/B channel (vertical col-
umn) intersects the MATRIX bus (horizontal row),
and turn the [DATA] encoder.
To switch the signal sent from a specific MIX or STE-
REO A/B channel to the MATRIX buses on/off, move
the cursor to the vertical column for that channel, and
press the [ENTER] key.
Hint
• If the send level is set above nominal (0 dB), a red line indi-
cating nominal level is displayed.
• If the send-destination MATRIX channel is paired, the grid
for the odd-numbered MATRIX bus will show an orange line
indicating the pan value instead of a bar graph. (In MTRX
from MIX mode, upward indicates R, and downward indi-
cates L.)
If the SEND LEVEL button is on, you can select a
desired grid and copy its send level (pan) value to other
channels (horizontal direction) or to other MATRIX
buses (vertical direction), or switch all grids on/off
simultaneously.
To do so, move the cursor to the desired grid; then
hold down the [SHIFT] key and press the [ENTER]
key. (Alternatively, hold down the [SHIFT] key and
click the desired grid.) When the JOB SELECT win-
Pan value (orange line)
Channels for which the
signal sent to the MATRIX
bus is turned on (blue bar
graph)
PM5D/PM5D-RH V2 / DSP5D Owner's Manual
dow appears, select one of the following choices to
copy, and click the OK button.
LEVEL COPY [ALL MATRIX
Copy the send level (pan) value of the selected grid to
all send level (pan) settings of the corresponding MIX
(or STEREO A/B) channel in the vertical direction of
the grid.
Note
If the selected grid is a send level, only the send levels will be
copied. If the selected grid is a pan value, only the pan values
will be copied.
LEVEL COPY [ALL MIX
Copy the send level (pan) value of the selected grid to
all send level (pan) settings of the corresponding
MATRIX bus in the horizontal direction of the grid.
LEVEL COPY [ALL MIX x ALL MATRIX]
Copy the send level (pan) value of the selected grid to
the send level (pan) settings of all MIX (and STEREO
A/B) channels and MATRIX buses.
ALL ON [ALL MIX
]
Turn on the signals sent from all channels (MIX,
STEREO A/B) to the corresponding MATRIX bus.
ALL OFF [ALL MIX
]
Turn off the signals sent from all channels (MIX,
STEREO A/B) to the corresponding MATRIX bus.
❏ When the SEND POINT button is on
The grid will show the position from which the signal is
sent from the MIX channels or STEREO A/B channels
to the MATRIX buses.
PRE FADER
POST FADER
Each indication has the following significance.
(yellow) . . PRE FADER (immediately
before the fader)
(gray) . . . . POST FADER (immediately
after the fader)
(red) . . . . . POST ON (immediately after
the [ON] key)
Reference section
]
]
POST ON
265

Advertisement

Table of Contents
loading

This manual is also suitable for:

Pm5d-rh v2Pm5dPm5d-rhPm5d v2Pm5d-ex

Table of Contents