Dual Pitch; Amp Simulate - Yamaha DSP5D Owner's Manual

Effects Parameters
❏ DUAL PITCH
Two input, two output pitch shifter.
Parameter Range
PITCH 1 –24 to +24 semitones Channel #1 pitch shift
FINE 1 –50 to +50 cents
LEVEL 1 –100 to +100%
PAN 1 L63 to R63
DELAY 1 0.0–1000.0 ms
FB. G 1 –99 to +99%
PITCH 2 –24 to +24 semitones Channel #2 pitch shift
FINE 2 –50 to +50 cents
LEVEL 2 –100 to +100%
PAN 2 L63 to R63
DELAY 2 0.0–1000.0 ms
FB. G 2 –99 to +99%
MODE 1–10
SYNC OFF/ON
*1
NOTE 1
NOTE 2 1
*1.
(Maximum value depends on the tempo setting)
❏ ROTARY
One input, two output rotary speaker simulator.
Parameter Range
ROTATE STOP, START
SPEED SLOW, FAST
SLOW 0.05–10.00 Hz
FAST 0.05–10.00 Hz
DRIVE 0–100
ACCEL 0–10
LOW 0–100
HIGH 0–100
❏ RING MOD.
Two input, two output ring modulator.
Parameter Range
SOURCE OSC, SELF
OSC FREQ 0.0–5000.0 Hz
FM FREQ. 0.05–40.00 Hz
FM DEPTH 0–100%
SYNC OFF/ON
*1
NOTE FM
*1.
328
PM5D/PM5D-RH V2 / DSP5D Owner's Manual
Description
Channel #1 pitch shift fine
Channel #1 level (plus values
for normal phase, minus values
for reverse phase)
Channel #1 pan
Channel #1 delay time
Channel #1 feedback gain (plus
values for normal-phase feed-
back, minus values for
reverse-phase feedback)
Channel #2 pitch shift fine
Channel #2 level (plus values
for normal phase, minus values
for reverse phase)
Channel #2 pan
Channel #2 delay time
Channel #2 feedback gain (plus
values for normal-phase feed-
back, minus values for
reverse-phase feedback)
Pitch shift precision
Tempo parameter sync on/off
Used in conjunction with
TEMPO to determine Channel
#1 delay
Used in conjunction with
TEMPO to determine Channel
#2 delay
Description
Rotation stop, start
Rotation speed (see SLOW and
FAST parameters)
SLOW rotation speed
FAST rotation speed
Overdrive level
Acceleration at speed changes
Low-frequency filter
High-frequency filter
Description
Modulation source: oscillator or
input signal
Oscillator frequency
Oscillator frequency modulation
speed
Oscillator frequency modulation
depth
Tempo parameter sync on/off
Used in conjunction with TEMPO
to determine FM FREQ
Reference section
❏ MOD. FILTER
Two input, two output modulation filter.
Parameter Range
FREQ. 0.05–40.00 Hz
DEPTH 0–100%
PHASE 0.00–354.38 degrees
TYPE LPF, HPF, BPF
OFFSET 0–100
RESO. 0–20
LEVEL 0–100
SYNC OFF/ON
*1
NOTE
*1.
❏ DISTORTION
One input, two output distortion effect.
Parameter Range
DST1, DST2, OVD1,
DST TYPE
OVD2, CRUNCH
DRIVE 0–100
MASTER 0–100
TONE –10 to +10
N. GATE 0–20
❏ AMP SIMULATE
One input, two output guitar amp simulator.
Parameter Range
*1
AMP TYPE
DST1, DST2, OVD1,
DST TYPE
OVD2, CRUNCH
DRIVE 0–100
MASTER 0–100
BASS 0–100
MIDDLE 0–100
TREBLE 0–100
CAB DEP 0–100%
EQ F 100–8.00 kHz
EQ G –12.0 to +12.0 dB
EQ Q 10.0–0.10
N. GATE 0–20
*1. STK-M1, STK-M2, THRASH, MIDBST, CMB-PG, CMB-VR, CMB-
DX, CMB-TW, MINI, FLAT
❏ DYNA. FILTER
Two input, two output dynamically controlled filter.
Parameter Range
Control source: input signal or
SOURCE INPUT, MIDI
MIDI Note On velocity
SENSE 0–100 Sensitivity
Upward or downward frequency
DIR. UP, DOWN
change
Filter frequency change decay
*1
DECAY
speed
TYPE LPF, HPF, BPF Filter type
OFFSET 0–100 Filter frequency offset
RESO. 0–20 Filter resonance
LEVEL 0–100 Output Level
*1. 6.0 ms–46.0 s (fs=44.1 kHz), 5.0 ms–42.3 s (fs=48 kHz),
3 ms–23.0 s (fs=88.2 kHz), 3 ms–21.1 s (fs=96 kHz)
Description
Modulation speed
Modulation depth
Left-channel modulation and
right-channel modulation
phase difference
Filter type: low pass, high pass,
band pass
Filter frequency offset
Filter resonance
Output level
Tempo parameter sync on/off
Used in conjunction with
TEMPO to determine FREQ
Description
Distortion type (DST = distortion,
OVD = overdrive)
Distortion drive
Master volume
Tone
Noise reduction
Description
Guitar amp simulation type
Distortion type (DST = distortion,
OVD = overdrive)
Distortion drive
Master volume
Bass tone control
Middle tone control
High tone control
Speaker cabinet simulation depth
EQ (peaking type) frequency
EQ (peaking type) gain
EQ (peaking type) bandwidth
Noise reduction
Description