Yamaha DSP5D Owner's Manual page 332

Effects Parameters
❏ DELAY→REV
One input, two output delay and reverb effects in series.
Parameter Range
DELAY L 0.0–1000.0 ms
DELAY R 0.0–1000.0 ms
FB. DLY 0.0–1000.0 ms
FB. GAIN –99 to +99%
DELAY HI 0.1–1.0
THRU, 21.2 Hz–
HPF
8.00 kHz
50.0 Hz–16.0 kHz,
LPF
THRU
DLY.BAL 0–100%
REV TIME 0.3–99.0 s
INI. DLY 0.0–500.0 ms
REV HI 0.1–1.0
DIFF. 0–10
DENSITY 0–100%
SYNC OFF/ON
*1
NOTE L
NOTE R *1
NOTE FB *1
*1.
(Maximum value depends on the tempo setting)
❏ DIST→DELAY
One input, two output distortion and delay effects in
series.
Parameter Range
DST1, DST2, OVD1,
DST TYPE
OVD2, CRUNCH
DRIVE 0–100
MASTER 0–100
TONE –10 to +10
N. GATE 0–20
DELAY 0.0–2725.0 ms
FB. GAIN –99 to +99%
HI. RATIO 0.1–1.0
FREQ. 0.05–40.00 Hz
DEPTH 0–100%
DLY.BAL 0–100%
SYNC OFF/ON
*1
DLY.NOTE
MOD.NOT
*2
E
*1.
(Maximum value depends on the tempo setting)
*2.
332
PM5D/PM5D-RH V2 / DSP5D Owner's Manual
Description
Left channel delay time
Right channel delay time
Feedback delay time
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feedback)
Delay high-frequency feedback
ratio
High-pass filter cutoff frequency
Low-pass filter cutoff frequency
Delay and delayed reverb balance
(0% = all delayed reverb, 100% =
all delay)
Reverb time
Initial delay before reverb begins
High-frequency reverb time ratio
Spread
Reverb density
Tempo parameter sync on/off
Used in conjunction with TEMPO
to determine left channel DELAY L
Used in conjunction with TEMPO
to determine right channel DELAY
R
Used in conjunction with TEMPO
to determine FB. DLY
Description
Distortion type (DST = distortion,
OVD = overdrive)
Distortion drive
Master volume
Tone control
Noise reduction
Delay time
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feed-
back)
High-frequency feedback ratio
Modulation speed
Modulation depth
Distortion and delay balance (0%
= all distortion, 100% = all
delayed distortion)
Tempo parameter sync on/off
Used in conjunction with TEMPO
to determine DELAY
Used in conjunction with TEMPO
to determine FREQ.
Reference section
❏ MULTI FILTER
Two input, two output 3-band multi-filter (24 dB/octave).
Parameter Range
Filter 1 type: high pass, low pass,
TYPE 1 HPF, LPF, BPF
band pass
Filter 2 type: high pass, low pass,
TYPE 2 HPF, LPF, BPF
band pass
Filter 3 type: high pass, low pass,
TYPE 3 HPF, LPF, BPF
band pass
FREQ. 1 28.0 Hz–16.0 kHz Filter 1 frequency
FREQ. 2 28.0 Hz–16.0 kHz Filter 2 frequency
FREQ. 3 28.0 Hz–16.0 kHz Filter 3 frequency
LEVEL 1 0–100 Filter 1 level
LEVEL 2 0–100 Filter 2 level
LEVEL 3 0–100 Filter 3 level
RESO. 1 0–20 Filter 1 resonance
RESO. 2 0–20 Filter 2 resonance
RESO. 3 0–20 Filter 3 resonance
❏ FREEZE
One input, one output basic sampler.
Parameter Range
In MANUAL mode, recording is
started by pressing the REC and
PLAY buttons. In INPUT mode,
REC MODE MANUAL, INPUT Record-Ready mode is engaged by
pressing the REC button, and
actual recording is triggered by the
input signal.
Recording delay. For plus values,
recording starts after the trigger is
–1000 to +1000
REC DLY received. For minus values, record-
ms
ing starts before the trigger is
received.
Input trigger level (i.e., the signal
TRG LVL –60 to 0 dB level required to trigger recording
or playback)
Once playback has been triggered,
subsequent triggers are ignored for
TRG MASK 0–1000 ms
the duration of the TRG MASK
time.
In MOMENT mode, the sample
plays only while the that the PLAY
button is pressed. In CONT mode,
playback continues once the PLAY
MOMENT,
PLY MODE button has been pressed. The
CONTI., INPUT
number of times the sample plays
is set using the LOOP NUM param-
eter. In INPUT mode, playback is
triggered by the input signal.
*1
START Playback start point in milliseconds
END 1 Playback end point in milliseconds
LOOP 1 Loop start point in milliseconds
LOOP
0–100 Number of times the sample plays
NUM
START
0–262000 Playback start point in samples
[SAMPLE]
END
0–262000 Playback end point in samples
[SAMPLE]
LOOP
0–262000 Loop start point in samples
[SAMPLE]
–12 to +12 semi-
PITCH Playback pitch shift
tones
FINE –50 to +50 cents Playback pitch shift fine
PLAY button can be triggered by
MIDI TRG OFF, C1–C6, ALL
using MIDI Note on/off messages.
*1. 0.0–5941.0 ms (fs=44.1 kHz), 0.0 ms–5458.3 ms (fs=48 kHz), 0.0–
2970.5 ms (fs=88.2 kHz), 0.0 ms–2729.2 ms (fs=96 kHz)
Description
Description