GE Discovery LS System Service Manual page 18

GE H
EALTHCARE
D 2307224-100, R
IRECTION EVISION
6.2.7
6.2.8
6.2.9
Page 18
6
6.2.6.11 Install the Table Bulkhead (If Necessary) ...................................................... 143
6.2.6.12 Install the Base Axis Motor I Cable (P/N 2323724) ....................................... 144
6.2.6.13 Install the Clutch Control I Cable (P/N 2340390)........................................... 145
6.2.6.14 Install Clutch Driver Unit (P/N 2340282)........................................................ 146
6.2.6.15 Install the Clutch Driver Unit Power Cable (P/N 2338088) ............................ 147
6.2.6.16 Attach the Ground Wire (P/N 2338084) to the Clutch Driver Unit ................. 148
6.2.6.17 Replace the ETC Interface Board.................................................................. 149
6.2.6.18 Install the Base CMD Adapter Cable (P/N 2338086) .................................... 150
6.2.6.19 Install the CT-PET Position Optical Sensor (P/N 2350570) .......................... 151
6.2.6.20 Install the Base Driver Enable Ribbon Cable (P/N 2340386) ........................ 152
6.2.6.21 Install Base CMD Adapter (P/N 2304737) ..................................................... 155
6.2.6.22 Attach Flanges (P/N 2320158) to the Secondary Base ................................. 157
6.2.6.23 Attach Clutch Motor Cables ........................................................................... 159
6.2.6.24 Reassemble the Secondary Base Drive Belt................................................. 161
6.2.6.25 Set the Table Position Pot ............................................................................. 164
6.2.6.26 Attach the CT-PET Position Latch Mounting Plate ........................................ 165
6.2.6.27 Install the PET-CT Position Latch Assembly ................................................. 166
6.2.6.28 Install the CT and PET Detent/Flag Assemblies ........................................... 168
6.2.6.29 If a PET Plug Is Required .............................................................................. 169
6.2.6.30 If a CT Plug Is Required ................................................................................ 170
6.2.6.31 Install the CT Detent and Flag Assembly ...................................................... 171
6.2.6.32 Install the PET Detent and Flag Assembly .................................................... 172
6.2.6.33 Assemble and Install PET Detent Adjuster.................................................... 173
6.2.6.34 Shim the PET Detent Assembly .................................................................... 174
6.2.6.35 Install Optical Sensor (P/N 2350570) ............................................................ 177
6.2.6.36 Align the Flag Plates to the Optical Sensor ................................................... 179
6.2.6.37 Install the Table Latch ................................................................................... 180
6.2.6.38 Adjust the Table Latch ................................................................................... 182
6.2.6.39 Install the New Characterization Bracket....................................................... 185
6.2.6.40 Install the Top Cover Brackets ...................................................................... 186
6.2.6.41 Install the Fourth Top Cover Bracket ............................................................. 187
6.2.6.42 Dress the Rest of the Cables and Close the ETC ......................................... 187
6.2.6.43 Install the Cosmetic Cradle Caps .................................................................. 188
Install Table Secondary Base Covers ........................................................................... 189
6.2.7.1 Automated Table Cover Components ........................................................... 189
6.2.7.2 Table Cover and Bracket Task List ............................................................... 190
6.2.7.3 Install the Roller Cover Assembly.................................................................. 191
6.2.7.4 Attach the Roller Cover Guides to the Secondary Base Side Rails .............. 191
6.2.7.5 Attach the Cover Bracket to the Secondary Base ......................................... 193
6.2.7.6 Reposition the Ground Bus Bar ..................................................................... 194
6.2.7.7 Attach Canister Brackets to Head End of the Secondary Base..................... 195
6.2.7.8 Attach the Drip Trough to the Roller Canister Assembly ............................... 196
6.2.7.9 Attach the Roller Cover Canister to the Secondary Base.............................. 197
6.2.7.10 Install the Idler Roller and Align it to the Roller Cover Guides....................... 198
6.2.7.11 Fasten the Side Skirts to the Secondary Base .............................................. 201
6.2.7.12 Attach the Interface Cover Between the DLS Table and Gantry ................... 203
6.2.7.13 Fasten the Rear Covers to the Secondary Base ........................................... 204
6.2.7.14 Attach the Top Cap Assembly to the Secondary Base.................................. 205
6.2.7.15 Attach the Back Cap to the Foot End of the Secondary Base ....................... 206
Finish the Mechanical Installation ................................................................................. 208
Completion .................................................................................................................... 210
Table of Contents
D LS S S
ISCOVERY YSTEM ERVICE
M
ANUAL