Output Terminal Function Selection (Pr.190 To Pr.192) - Mitsubishi Electric FR-E700EX Instruction Manual

Function assignment of external terminal and control

4.12.5 Output terminal function selection (Pr.190 to Pr.192)

You can change the functions of the open collector output terminal and relay output terminal.
Parameter
number
190
RUN terminal function
selection
191
FU terminal function
selection
192
A,B,C terminal function
selection
The above parameters can be set when Pr.160 Extended function display selection = "0". (Refer to page 182)

The setting values "93" and "193" are available only in Pr.190 and Pr.191.

The setting values "68" and "168" are valid only when used with FR-E7DS. (For the details, refer to the Instruction Manual of FR-E7DS.)
...... Specifications differ according to the date assembled. Refer to page 316 to check the SERIAL number.
(1) Output signal list
 You can set the functions of the output terminals.
 Refer to the following table and set the parameters: (0 to 99: positive logic, 100 to 199: negative logic)
Setting
Signal
Positive Negative
logic logic
0 100 RUN
1 101 SU
3 103 OL
4 104 FU
7 107 RBP
8 108 THP
11 111 RY
12 112 Y12
13 113 Y13
144
Name
Open
collector
output
terminal
Relay
output
terminal
Function
Speed
control
Drive unit running
Position
control
Speed
control
Up to speed
Position
control
Overload alarm Output while torque limit function is activated.
Output when the rotation speed reaches the speed
Rotation speed detection
set in Pr.42 (Pr.43 for reverse rotation).
Regenerative brake pre- Output when 85% of the regenerative brake duty set
alarm in Pr.70 is reached.
Output when the electronic thermal value reaches
Electronic thermal O/L 85% of the trip level. (Electronic thermal relay
relay pre-alarm function protection (E.THT/E.THM) activates, when
the value reached 100%.)
Output when reset process is completed (when the
drive unit can be started by switching the start signal
Drive unit operation ready
ON or while it is running) after power-ON of the drive
unit.
Output when the output current is the Pr.150 setting or
Output current detection
higher for longer than the time set in Pr.151.
Output when the output power is the Pr.152 setting or
Zero current detection
lower for longer than the time set in Pr.153.
Initial
Initial signal
value
RUN (drive unit
0
runnning)
FU (rotation speed
4
detection)
99 ALM (fault output)
Operation
Output when the drive unit starts running
upon turning ON of the start signal.
Turned OFF when the drive unit performs
deceleration stop and zero speed control
or servo lock is activated.
Same operation as that of the RY2 signal
Output when the rotation speed is reached
to the set speed.

Setting range
0, 1, 3, 4, 7, 8, 11 to 16, 21,
24 to 26, 33, 36, 38, 47, 55, 56,
60, 61, 63, 64, 68, 90, 91, 93,
95, 96, 98, 99, 100, 101, 103,
104, 107, 108, 111 to 116, 121,
124 to 126, 133, 136, 138, 147,
155, 156, 160, 161, 163, 164,
168, 190, 191, 193, 195, 196,
198, 199, 9999
Refer
Related
to
parameter
page

147
Pr.41, Pr.870 149
Pr.22, Pr.48,
111
Pr.156, Pr.157
Pr.42, Pr.43,
149
Pr.870
Pr.70 136
Pr.9 130

147
Pr.150, Pr.151 150
Pr.152, Pr.153 150