Table of Contents
Advertisement
U U n n p p l l u u g g t t h h e e f f r r y y e e r r f f r r o o m m t t h h e e p p o o w w e e r r s s o o u u r r c c e e b b e e f f o o r r e e p p e e r r f f o o r r m m i i n n g g
t t h h i i s s p p r r o o c c e e d d u u r r e e . . V V o o l l t t a a g g e e i i s s p p r r e e s s e e n n t t , , w w h h i i c c h h m m a a y y c c a a u u s s e e
s s e e v v e e r r e e i i n n j j u u r r y y . .
E E n n s s u u r r e e t t h h e e o o i i l l i i s s d d r r a a i i n n e e d d f f r r o o m m t t h h e e f f r r y y e e r r ' ' s s v v a a t t , , a a n n d d t t h h a a t t a a l l l l
m m e e t t a a l l s s u u r r f f a a c c e e s s a a r r e e c c o o o o l l t t o o t t h h e e t t o o u u c c h h b b e e f f o o r r e e p p e e r r f f o o r r m m i i n n g g t t h h i i s s
p p r r o o c c e e d d u u r r e e . . W W o o r r k k i i n n g g o o n n t t h h e e f f r r y y e e r r w w h h i i l l e e h h o o t t o o i i l l o o r r s s u u r r f f a a c c e e s s
a a r r e e p p r r e e s s e e n n t t m m a a y y c c a a u u s s e e s s e e v v e e r r e e i i n n j j u u r r y y . .
Ensure the oil is drained from the vat and drain pan, remove the drain pan and
1 1 ) )
set aside, and then remove the power from the fryer.
Standing in front of the fryer, remove the right-side panel to access the filter
2 2 ) )
pump motor.
Using an adjustable wrench, disconnect the flex lines from the inlet and outlet
3 3 ) )
sides of the JIB / ATO filter pump. See
Components , page 154
Using a wrench, remove the two locknuts holding the JIB / ATO pump mount
4 4 ) )
(base) to the fryer's frame.
Using a wrench, remove the two locknuts holding the JIB / ATO pump cover to
5 5 ) )
the mount (base) to access the wiring.
Remove the pump cover, and then disconnect the wiring as required.
6 6 ) )
Using a wrench, remove the four locknuts holding the JIB / ATO pump to the
7 7 ) )
mount, and then remove the JIB / ATO pump.
Insert four new grommets, included with the JIB / ATO pump kit, through the
8 8 ) )
bottom of the JIB / ATO pump base.
Using a wrench, install the new JIB / ATO pump to the mount securing with four
9 9 ) )
locknuts.
Reconnect the JIB / ATO pump wiring, and then reinstall the pump cover.
1 1 0 0 ) )
Using a wrench, install the pump cover to the pump mount (base) securing with
1 1 1 1 ) )
two locknuts.
Using a wrench, install the JIB / ATO pump mount (base) to the fryer's frame
1 1 2 2 ) )
securing with two locknuts.
Using an adjustable wrench, connect the flex lines to the inlet and outlet sides of
1 1 3 3 ) )
the JIB / ATO filter pump. Torque to 32 ft. lbs. (43.39 Nm).
Replace the drain pan, reconnect the power, add oil to the vat, and then run a
1 1 4 4 ) )
filter cycle while checking for leaks.
If leaks are discovered, repair as necessary.
1 1 5 5 ) )
Install the right-side panel.
1 1 6 6 ) )
Figure 10-7 Motors and Plumbing
for connection, configuration and orientation.
121
Advertisement
Table of Contents
