Table of Contents
Advertisement
C C h h a a p p t t e e r r 9 9 C C o o m m p p o o n n e e n n t t
R R e e p p l l a a c c e e m m e e n n t t P P r r o o c c e e d d u u r r e e s s
This section provides replacement procedures, for common parts of the fryer.
D D o o n n o o t t m m o o v v e e t t h h e e f f r r y y e e r r w w i i t t h h h h o o t t o o i i l l i i n n t t h h e e v v a a t t o o r r f f i i l l t t e e r r p p a a n n . .
S S e e v v e e r r e e b b u u r r n n s s c c a a n n r r e e s s u u l l t t f f r r o o m m s s p p l l a a s s h h i i n n g g h h o o t t o o i i l l . .
9 9 . . 1 1 C C o o n n t t r r o o l l P P a a n n e e l l R R e e p p l l a a c c e e m m e e n n t t
Figure 10-1 Components, Front , page 141
Refer to
number.
U U n n p p l l u u g g t t h h e e f f r r y y e e r r f f r r o o m m t t h h e e p p o o w w e e r r s s o o u u r r c c e e b b e e f f o o r r e e p p e e r r f f o o r r m m i i n n g g
t t h h i i s s p p r r o o c c e e d d u u r r e e . . V V o o l l t t a a g g e e i i s s p p r r e e s s e e n n t t , , w w h h i i c c h h m m a a y y c c a a u u s s e e
s s e e v v e e r r e e i i n n j j u u r r y y . .
Ensure power is removed from the fryer.
1 1 ) )
Using a Phillips head screwdriver, remove two screws in the front of the old
2 2 ) )
control panel, and then rotate the panel down.
Obtain the new control board and note the label on the back, which identifies the
3 3 ) )
connection locations.
One by one remove the connectors from the old control panel and plug them in
4 4 ) )
to the new control panel.
Replace the old control panel with the new control panel, and then rotate the
5 5 ) )
new control panel up and install the two securing screws.
Test the new control panel to ensure it works properly.
6 6 ) )
9 9 . . 2 2 R R e e s s e e t t C C i i r r c c u u i i t t B B r r e e a a k k e e r r R R e e p p l l a a c c e e m m e e n n t t
Refer to
Figure 10-1 Components, Front , page 141
number.
U U n n p p l l u u g g t t h h e e f f r r y y e e r r f f r r o o m m t t h h e e p p o o w w e e r r s s o o u u r r c c e e b b e e f f o o r r e e p p e e r r f f o o r r m m i i n n g g
t t h h i i s s p p r r o o c c e e d d u u r r e e . . V V o o l l t t a a g g e e i i s s p p r r e e s s e e n n t t , , w w h h i i c c h h m m a a y y c c a a u u s s e e
s s e e v v e e r r e e i i n n j j u u r r y y . .
Ensure power is removed from the fryer.
1 1 ) )
Using a Phillips head screwdriver, remove two screws in the front of the control
2 2 ) )
panel, and then rotate the panel down. Remove if necessary.
Using a 9/16 in. wrench, loosen and remove the locknut on the outside (shroud)
3 3 ) )
of the reset button.
for location, illustration and part
for location, illustration and part
107
Advertisement
Table of Contents
