Table of Contents
Advertisement
Using an adjustable wrench and Loctite where applicable, connect the inlet and
5 5 ) )
outlet plumbing. See
for connection, configuration and orientation.
Tighten the four nuts and washers holding the filter pump/motor to the frame.
6 6 ) )
Replace the drain pan, reconnect the power, add oil to the vat, and then run a
7 7 ) )
filter cycle while checking for leaks.
If leaks are discovered, repair as necessary.
8 8 ) )
Install the left and right side panels.
9 9 ) )
9 9 . . 1 1 4 4 F F i i l l t t e e r r P P u u m m p p C C h h e e c c k k V V a a l l v v e e R R e e p p l l a a c c e e m m e e n n t t
Refer to
Figure 10-7 Motors and Plumbing Components , page 154
illustration, part numbers, configuration, and orientation of the plumbing components.
Ensure the oil is drained from the vat and drain pan, remove the drain pan and
1 1 ) )
set aside, and then remove the power from the fryer.
Access the pump motor check valve on the back of the fryer and note the
2 2 ) )
plumbing configuration. See
page 154
Using a crescent wrench, disconnect the old check valve.
3 3 ) )
Add white Loctite to the non-compression fitting threads on the new check valve
4 4 ) )
and plumbing. Do not use Loctite on compression fittings.
Using a crescent wrench, connect the new check valve.
5 5 ) )
Replace the drain pan, reconnect the power, add oil to the vat, and then run a
6 6 ) )
filter cycle while checking for leaks.
If leaks are discovered, repair as necessary.
7 7 ) )
9 9 . . 1 1 5 5 J J I I B B / / A A T T O O P P u u m m p p R R e e p p l l a a c c e e m m e e n n t t
Refer to
Figure 10-7 Motors and Plumbing Components , page 154
illustration and part number.
120
Figure 10-7 Motors and Plumbing Components , page 154
U U n n p p l l u u g g t t h h e e f f r r y y e e r r f f r r o o m m t t h h e e p p o o w w e e r r s s o o u u r r c c e e b b e e f f o o r r e e p p e e r r f f o o r r m m i i n n g g
t t h h i i s s p p r r o o c c e e d d u u r r e e . . V V o o l l t t a a g g e e i i s s p p r r e e s s e e n n t t , , w w h h i i c c h h m m a a y y c c a a u u s s e e
s s e e v v e e r r e e i i n n j j u u r r y y . .
E E n n s s u u r r e e t t h h e e o o i i l l i i s s d d r r a a i i n n e e d d f f r r o o m m t t h h e e f f r r y y e e r r ' ' s s v v a a t t , , a a n n d d t t h h a a t t a a l l l l
m m e e t t a a l l s s u u r r f f a a c c e e s s a a r r e e c c o o o o l l t t o o t t h h e e t t o o u u c c h h b b e e f f o o r r e e p p e e r r f f o o r r m m i i n n g g t t h h i i s s
p p r r o o c c e e d d u u r r e e . . W W o o r r k k i i n n g g o o n n t t h h e e f f r r y y e e r r w w h h i i l l e e h h o o t t o o i i l l o o r r s s u u r r f f a a c c e e s s
a a r r e e p p r r e e s s e e n n t t m m a a y y c c a a u u s s e e s s e e v v e e r r e e i i n n j j u u r r y y . .
Figure 10-7 Motors and Plumbing Components ,
for connection and orientation.
for location,
for location,
Advertisement
Table of Contents
