Table of Contents
Advertisement
Using a Phillips head screwdriver, remove two screws in the front of the control
2 2 ) )
panel, and then rotate the panel down. Remove if necessary.
Place the momentary switch in the on position, and then using a multimeter test
3 3 ) )
across the switch terminals.
Place the momentary switch in the off position, and then using a multimeter test
4 4 ) )
across the switch terminals.
With the switch in the ON position, the circuit should be closed. With the switch in the
OFF position, the circuit should be open. If the switch checks defective, replace by
continuing with this procedure.
Disconnect the wires from momentary switch, and then push in on tabs to
5 5 ) )
remove from the lower-front panel. I I N N F F O O : Reverse the order by removing the
part, and then wires if easier.
Press the new switch in to the front panel, and then reconnect the wires.
6 6 ) )
Install the control panel, and then test the new switch to ensure it works
7 7 ) )
properly.
9 9 . . 5 5 U U S S B B P P o o r r t t R R e e p p l l a a c c e e m m e e n n t t
Refer to
Figure 10-1 Components, Front , page 141
number.
U U n n p p l l u u g g t t h h e e f f r r y y e e r r f f r r o o m m t t h h e e p p o o w w e e r r s s o o u u r r c c e e b b e e f f o o r r e e p p e e r r f f o o r r m m i i n n g g
t t h h i i s s p p r r o o c c e e d d u u r r e e . . V V o o l l t t a a g g e e i i s s p p r r e e s s e e n n t t , , w w h h i i c c h h m m a a y y c c a a u u s s e e
s s e e v v e e r r e e i i n n j j u u r r y y . .
Ensure power is removed from the fryer.
1 1 ) )
Using a Phillips head screwdriver, remove two screws in the front of the control
2 2 ) )
panel, and then rotate the panel down. Remove if necessary.
Disconnect the wires from the USB port, and then push in on tabs to remove
3 3 ) )
from the front panel.
Press the new USB port in to the front panel, and then reconnect the wires.
4 4 ) )
Install the control panel, and then test the new USB port to ensure it works
5 5 ) )
properly.
9 9 . . 6 6 H H i i g g h h L L i i m m i i t t M M o o d d u u l l e e R R e e p p l l a a c c e e m m e e n n t t
Figure 10-6 Control Shroud , page 152
Refer to
number.
U U n n p p l l u u g g t t h h e e f f r r y y e e r r f f r r o o m m t t h h e e p p o o w w e e r r s s o o u u r r c c e e b b e e f f o o r r e e p p e e r r f f o o r r m m i i n n g g
t t h h i i s s p p r r o o c c e e d d u u r r e e . . V V o o l l t t a a g g e e i i s s p p r r e e s s e e n n t t , , w w h h i i c c h h m m a a y y c c a a u u s s e e
s s e e v v e e r r e e i i n n j j u u r r y y . .
for location, illustration and part
for location, illustration and part
109
Advertisement
Table of Contents
