Table of Contents
Advertisement
Parameter Descriptions
4.2.2 1-1* Motor Selection
Parameter group for setting general motor data. The parameters cannot be adjusted while the motor is running.
The active parameters are shown in Table 4.2. x indicates that a particular parameter is active when the option is selected.
Parameter 1-10 Motor Construction
Parameter 1-00 Configuration Mode
Parameter 1-03 Torque Characteristics
Parameter 1-06 Clockwise Direction
Parameter 1-08 Motor Control Bandwidth
Parameter 1-14 Damping Gain
Parameter 1-15 Low Speed Filter Time Const.
Parameter 1-16 High Speed Filter Time Const.
Parameter 1-17 Voltage filter time const.
Parameter 1-20 Motor Power [kW]
Parameter 1-22 Motor Voltage
Parameter 1-23 Motor Frequency
Parameter 1-24 Motor Current
Parameter 1-25 Motor Nominal Speed
Parameter 1-26 Motor Cont. Rated Torque
Parameter 1-29 Automatic Motor Adaption (AMA)
Parameter 1-30 Stator Resistance (Rs)
Parameter 1-33 Stator Leakage Reactance (X1)
Parameter 1-35 Main Reactance (Xh)
Parameter 1-37 d-axis Inductance (Ld)
Parameter 1-38 q-axis Inductance (Lq)
Parameter 1-39 Motor Poles
Parameter 1-40 Back EMF at 1000 RPM
Parameter 1-42 Motor Cable Length
Parameter 1-43 Motor Cable Length Feet
Parameter 1-44 d-axis Inductance Sat. (LdSat)
Parameter 1-45 q-axis Inductance Sat. (LqSat)
Parameter 1-46 Position Detection Gain
Parameter 1-48 Current at Min Inductance for d-axis
Parameter 1-49 Current at Min Inductance for q-axis
Parameter 1-50 Motor Magnetisation at Zero Speed
Parameter 1-52 Min Speed Normal Magnetising [Hz]
Parameter 1-55 U/f Characteristic - U
Parameter 1-56 U/f Characteristic - F
Parameter 1-62 Slip Compensation
Parameter 1-63 Slip Compensation Time Constant
Parameter 1-64 Resonance Dampening
Parameter 1-65 Resonance Dampening Time Constant
Parameter 1-66 Min. Current at Low Speed
Parameter 1-70 PM Start Mode
Parameter 1-71 Start Delay
Parameter 1-72 Start Function
Parameter 1-73 Flying Start
Parameter 1-80 Function at Stop
Parameter 1-90 Motor Thermal Protection
Parameter 2-00 DC Hold Current
Parameter 2-01 DC Brake Current
MG06C602
Programming Guide
[0] Asynchron
[1] PM Motor non
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Danfoss A/S © 7/2015 All rights reserved.
[2] PM, salient IPM,
salient
non-Sat
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
[3] PM, salient IPM,
Sat
4
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
27
4
Advertisement
Table of Contents
Need help?
Do you have a question about the VLT Automation Drive FC 360 and is the answer not in the manual?