Danfoss VLT Automation Drive FC 360 Programming Manual page 133

Parameter Lists
Par. No. # Parameter description
7-36 Process PID Diff. Gain Limit
7-38 Process PID Feed Forward Factor
7-39 On Reference Bandwidth
7-4* Adv. Process PID I
7-40 Process PID I-part Reset
7-41 Process PID Output Neg. Clamp
7-42 Process PID Output Pos. Clamp
7-43 Process PID Gain Scale at Min. Ref.
7-44 Process PID Gain Scale at Max. Ref.
7-45 Process PID Feed Fwd Resource
7-46 Process PID Feed Fwd Normal/ Inv. Ctrl.
7-48 PCD Feed Forward
7-49 Process PID Output Normal/ Inv. Ctrl.
7-5* Adv. Process PID II
7-50 Process PID Extended PID
7-51 Process PID Feed Fwd Gain
7-52 Process PID Feed Fwd Ramp up
7-53 Process PID Feed Fwd Ramp down
7-56 Process PID Ref. Filter Time
7-57 Process PID Fb. Filter Time
7-6* Feedback Conversion
7-60 Feedback 1 Conversion
7-62 Feedback 2 Conversion
5.2.9 8-** Communications and Options
Par. No. # Parameter description
8-0* General Settings
8-01 Control Site
8-02 Control Source
8-03 Control Timeout Time
8-04 Control Timeout Function
8-07 Diagnosis Trigger
8-1* Ctrl. Word Settings
8-10 Control Word Profile
8-14 Configurable Control Word CTW
8-19 Product Code
8-3* FC Port Settings
8-30 Protocol
8-31 Address
8-32 Baud Rate
8-33 Parity/Stop Bits
8-35 Minimum Response Delay
8-36 Maximum Response Delay
8-37 Maximum Inter-char delay
8-4* FC MC protocol set
8-42 PCD Write Configuration
8-43 PCD Read Configuration
8-5* Digital/Bus
MG06C602
Programming Guide
Default value
5 N/A
0%
5%
[0] No
-100 %
100%
100%
100%
[0] No function
[0] Normal
0 N/A
[0] Normal
[1] Enabled
1 N/A
0.01 s
0.01 s
0.001 s
0.001 s
[0] Linear
[0] Linear
Default value
[0] Digital and ctrl.word
ExpressionLimit
1 s
[0] Off
[0] Disable
[0] FC profile
[1] Profile default
ExpressionLimit
[0] FC
1 N/A
ExpressionLimit
ExpressionLimit
0.01 s
ExpressionLimit
0.025 s
ExpressionLimit
ExpressionLimit
Danfoss A/S © 7/2015 All rights reserved.
2-set-up Change Conversion
during
operation
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
2-set-up Change Conversion
during
operation
All set-ups TRUE
All set-ups TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
All set-ups TRUE
All set-ups TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
Type
index
-1 Uint16
0 Uint16
0 Uint8
– Uint8
0 Int16
0 Int16
0 Int16
5
0 Int16
– Uint8
– Uint8
0 Uint16
– Uint8
– Uint8
-2 Uint16
-2 Uint32
-2 Uint32
-3 Uint16
-3 Uint16
– Uint8
– Uint8
Type
index
– Uint8
– Uint8
-1 Uint16
– Uint8
– Uint8
– Uint8
– Uint8
0 Uint32
– Uint8
0 Uint8
– Uint8
– Uint8
-3 Uint16
-3 Uint16
-3 Uint16
– Uint8
– Uint8
131
5