Danfoss VLT Automation Drive FC 360 Programming Manual page 137

Parameter Lists
Par. No. # Parameter description
14-32 Current Lim Ctrl, Filter Time
14-4* Energy Optimising
14-40 VT Level
14-41 AEO Minimum Magnetisation
14-44 d-axis current optimization for IPM
14-5* Environment
14-50 RFI Filter
14-51 DC-Link Voltage Compensation
14-52 Fan Control
14-55 Output Filter
14-6* Auto Derate
14-61 Function at Inverter Overload
14-63 Min Switch Frequency
Dead Time Compensation Zero
14-64 Current Level
Speed Derate Dead Time Compen-
14-65 sation
14-8* Options
14-89 Option Detection
14-9* Fault Settings
14-90 Fault Level
5.2.14 15-** Drive Information
Par. No. # Parameter description
15-0* Operating Data
15-00 Operating hours
15-01 Running Hours
15-02 kWh Counter
15-03 Power Up's
15-04 Over Temp's
15-05 Over Volt's
15-06 Reset kWh Counter
15-07 Reset Running Hours Counter
15-3* Alarm Log
15-30 Alarm Log: Error Code
15-31 InternalFaultReason
15-4* Drive Identification
15-40 FC Type
15-41 Power Section
15-42 Voltage
15-43 Software Version
15-44 Ordered TypeCode
15-45 Actual Typecode String
15-46 Drive Ordering No
15-48 LCP Id No
15-49 SW ID Control Card
15-50 SW ID Power Card
MG06C602
Programming Guide
Default value 4-set-up
5 ms All set-ups
66% All set-ups
66% All set-ups
100% All set-ups
[2] Grid Type 1 set-up
[1] On All set-ups
[5] Constant-on mode 1 set-up
[0] No Filter 1 set-up
[0] Trip All set-ups
[2] 2.0 kHz 1 set-up
[0] Disabled All set-ups
ExpressionLimit All set-ups
[0] Protect Option
Config. 1 set-up
[3] Trip Lock All set-ups
Default value 2-set-up
0 h 1 set-up
0 h 1 set-up
0 kWh 1 set-up
0 N/A 1 set-up
0 N/A 1 set-up
0 N/A 1 set-up
[0] Do not reset 1 set-up
[0] Do not reset 1 set-up
0 N/A 1 set-up
0 N/A 1 set-up
0 N/A 1 set-up
0 N/A 1 set-up
0 N/A 1 set-up
0 N/A 1 set-up
0 N/A 1 set-up
0 N/A All set-ups
0 N/A 1 set-up
0 N/A 1 set-up
0 N/A 1 set-up
0 N/A 1 set-up
Danfoss A/S © 7/2015 All rights reserved.
Change Conversion
during index
operation
TRUE -4
FALSE 0
FALSE 0
TRUE 0
FALSE -
FALSE -
TRUE -
FALSE -
TRUE -
FALSE -
FALSE -
FALSE 0
TRUE -
TRUE -
Change Conversion
during index
operation
TRUE 74
TRUE 74
TRUE 75
TRUE 0
TRUE 0
TRUE 0
TRUE –
TRUE –
TRUE 0
TRUE 0
FALSE 0 VisStr[7]
FALSE 0 VisStr[20]
FALSE 0 VisStr[20]
FALSE 0 VisStr[20]
FALSE 0 VisStr[41]
FALSE 0 VisStr[40]
FALSE 0 VisStr[9]
FALSE 0 VisStr[21]
FALSE 0 VisStr[21]
FALSE 0 VisStr[21]
Type
Uint16
Uint8
Uint8
Uint8
Uint8
Uint8
5 5
Uint8
Uint8
Uint8
Uint8
Uint8
Uint16
Uint8
Uint8
Type
Uint32
Uint32
Uint32
Uint32
Uint16
Uint16
Uint8
Uint8
Uint8
Int16
135