Piper PA-28-236 DAKOTA Manuals

Manuals and User Guides for Piper PA-28-236 DAKOTA. We have 2 Piper PA-28-236 DAKOTA manuals available for free PDF download: Maintenance Manual, Pilot Operating Handbook

Piper PA-28-236 DAKOTA Maintenance Manual

Piper PA-28-236 DAKOTA Maintenance Manual (617 pages)

Brand: Piper | Category: Aircrafts | Size: 6.59 MB

Table of Contents

Vendor Publications
3
Piper Publications
4
Aerofiche Explanation and Revision Status
5
Effectivity Codes
5
Serial Number Information
6
Index Guide
7
Table of Contents
9
List of Illustrations
9
List of Charts
15
Airworthiness Limitations Table of Contents
18
General
20
Time Limits/Maintenance Checks Contents
22
Time Limits
24
Chapter 5 - Time Limits/Maintenance Checks

24
- Inspection Requirements
  24
- Preflight Checks
  24
- Overlimits Inspection
  24
- General
  24
- Scheduled Maintenance
  25
- Periodic Inspections
  25
- Programmed Inspection
  35
- Unscheduled Maintenance Checks
  35
  - Special Inspections as Required
    35
  - Dimensions and Areas Contents
    37
  - Leading Particulars and Principal Dimensions
    39
  - Three View
    41
  - Station Reference Lines
    42
  - Access and Inspection Provisions
    43
  - Access Plates and Panels
    43
  - Lifting and Shoring Contents
    45
  - Jacking
    47
  - Jacking Arrangement
    47
  - Leveling and Weighing Contents
    50
  - Leveling
    52
  - Weighing Airplane
    52
  - Leveling Longitudinally
    53
  - Leveling Laterally
    53
  - Towing and Taxiing Contents
    55
  - Towing
    57
  - Taxiing
    57
  - Parking and Mooring Contents
    59
  - Parking
    61
  - Mooring
    61
  - Required Placards Contents
    63
  - Exterior Placards and Markings
    65
  - Placards and Decals
    65
  - Interior Placards and Markings
    66
  - Servicing Contents
    68
  - Fuel System
    69
  - Filling Fuel Tanks
    69
  - Draining Moisture from Fuel System
    69
  - Fuel Filter Bowl and Screen
    70
Chapter 12 - Servicing

70
- Draining Fuel System 1C22
  70
- Oil System 1C22
  70
- Servicing Oil System 1C22
  70
- Draining Oil Sump 1C23
  71
- Filling Oil Sump 1C23
  71
- Oil Screen (Suction) 1C23
  71
- Recommendations for Changing Oil 1C23
  71
- Oil Filter (Full Flow) 1C24
  72
- Scheduled Servicing 1C24
  72
- Fuel System 1C24
  72
- Servicing Fuel System 1C24
  72
- Landing Gear 1D1
  73
- Servicing Landing Gear 1D1
  73
  - Servicing Points
    74
  - Filling Nose Gear Oleo Strut 1D3
    75
  - Servicing Oleo Struts 1D3
    75
  - Filling Main Gear Oleo Strut 1D4
    76
  - Brake System 1D7
    79
  - Draining Brake System 1C7
    79
  - Filling Brake Cylinder Reservoir 1C7
    79
  - Inflating Oleo Struts 1D7
    79
  - Servicing Brake System 1D7
    79
  - Servicing Tires 1D7
    79
  - Engine Air Filter 1D8
    80
  - Power Plant 1D8
    80
  - Servicing Power Plant 1D8
    80
  - Servicing Propeller 1D8
    80
  - Battery Box Corrosion Prevention 1D9
    81
  - Lubrication Instructions 1D9
    81
  - Servicing Electrical System 1D9
    81
  - Application of Grease 1D10
    82
  - Application of Oil 1D10
    82
  - Lubrication Chart 1D10
    82
  - Thread Lubricants
    83
  - Type of Lubricants
    84
  - Lubrication Chart (Landing Gear, Main)
    86
  - Landing Gear, Nose
    87
  - Control System
    88
  - Cabin Door, Baggage Door and Seat
    92
  - Power Plant, Propeller and Control Pivot Points
    93
  - Air Conditioning Condenser
    94
  - Standard Parctices - Airframe Contents
    98
  - Standard Practices - Airframe
    100
  - Torque Wrenches
    100
  - Torque Wrench Extension
    101
  - Correct Method of Installing Rod End Bearings
    101
  - Cherrylock Rivet Removal
    102
  - Identification of Fluid Lines
    103
  - Flareless Tube Assemblies
    103
  - Hose/Line Markings
    104
  - Flareless Tube Fittings
    105
  - Maximum Distance between Supports for Fluid Tubing
    106
  - Lubrication of Gaskets and Seals
    107
  - Aircraft Finish Care
    107
  - Cleaning Interior Surfaces
    107
  - Headliner, Side Panels and Seats
    107
  - Cleaning Exterior Surfaces
    108
  - Windshield and Windows
    108
  - Landing Gear
    109
  - Engine Compartment
    109
  - Conditions Affecting Corrosion
    110
  - Inspection
    110
  - Corrosion Removal and Control
    110
  - Types of Metal Corrosion
    111
  - Before Beginning any Rework
    111
  - Proceed as Follows
    111
  - Areas Prone to Corrosion
    112
  - Painting Safety
    113
  - Paint Application
    114
  - Painting Sequence
    114
  - Color Matching
    115
  - Polyurethane Paint Safety
    115
  - Dupont Imron Method
    116
  - Randolph Ranthane Method
    117
  - Alumigrip Method
    118
  - Titane Polyurethane Method
    119
  - Ameron Method
    119
  - Application of Acrylics
    120
  - Randacryl Method
    120
  - Trim and Registration Numbers
    121
  - Paint System Compatibility
    121
  - Common Paint Troubles
    122
  - Storage
    122
  - Painting Facility
    122
  - Waxing
    123
  - Paper Decals
    123
  - Vinyl Film Decals
    123
  - Metal Decals
    123
  - Environmental System Contents
    126
- Test Gauge and Manifold Set 1G6
  126
  - Heating
    128
  - Description and Operation
    128
  - Heater Maintenance
    128
  - Cabin Heater. Defroster and Fresh Air System
    129
  - Cooling
    130
  - Troubleshooting (Air Conditioner)
    131
  - Air Conditioning System Installation (Typical)
    137
  - Servicing Cooling System
    138
  - Malfunction Detection
    138
  - Temperature Pressure
    139
  - Special Servicing Procedures
    140
  - System Servicing Precautions
    140
  - Service Valves
    141
  - Aluminum Tubing Torque
    141
  - Service Valve Replacement
    142
  - Test Gauge and Manifold Set
    143
  - Checking the System for Leaks
    143
  - Manifold Set Operation
    144
  - Leak Check
    145
  - Leak Test Hookup
    145
  - Dishcarging
    146
  - Evacuating the System
    147
  - Evacuation Hookup
    147
  - System Vacuum
    147
  - Charging the System
    148
  - With a Charging Stand
    149
  - Charging Stand
    149
  - Using the Airplane Compressor to Charge the System
    150
  - Addition of Partial Charge to System
    151
  - Charging Hookup
    151
  - Compressor Service
    152
  - Compressor Removal
    152
  - Compressor Installation
    153
  - Checking Compressor Oil
    153
  - Replacement of Compressor Drive Belt
    154
  - Compressor and Fabricated Oil Dipstick
    154
  - Compressor Oil Charge
    154
  - Compressor and Alternator Belt Installation
    155
  - Adjustment of Drive Belt Tension
    156
  - Magnetic Clutch Removal
    157
  - Magnetic Clutch Installation
    157
  - Refrigerant Lines and Routing
    158
  - Receiver-Dehydrator Removal
    159
  - Receiver-Dehydrator Installation
    159
  - Condenser Removal
    159
  - Condenser Installation
    160
  - Condenser Door Actuator
    160
  - Condenser Assembly Rigging Instructions
    160
  - Condenser Air Scoop Installation
    161
  - Expansion Valve Removal
    162
  - Expansion Valve Installation
    162
  - Evaporator Removal
    163
  - Evaporator Installation
    163
  - Pressure Relief Switch
    164
  - Electrical Installation
    164
  - Components Installation
    164
  - Adjustment of Throttle Switch
    165
  - Fuse Replacement
    165
  - Overhead Vent Blower
    165
  - Removal/Disassembly of Blower Assembly
    165
  - Overhead Vent System
    166
  - Reassembly of Blower Assembly
    167
  - Installation of Blower Assembly
    167
  - Blower System Wire Color Codes
    167
  - Autoflight Contents
    170
  - Autopilot
    171
  - Piper AFCS Equipment
    172
  - Communications Contents
    174
  - Avionics Master and Emergency Switch Circuit
    175
  - Data Transmission and Automatic Calling
    176
  - Emergency Locator Transmitter
    176
  - Battery Removal and Installation
    176
  - Communications Components ELT Schematic
    177
  - Emergency Locator Transmitter Schematic
    177
  - ELT Portable Folding Antenna
    179
  - ELT Using Fixed Aircrat Antenna
    179
  - Testing Emergency Locator Transmitter
    180
  - Electrical Power Contents
    183
  - Troubleshooting (Alternator)
    186
  - Troubleshooting (Battery)
    191
  - DC Generation
    193
  - Checking Alternator System
    194
  - Service Precautions
    195
  - Lamp-Bank Load
    195
  - Overhaul of Alternator
    196
  - Alternator System
    196
  - Bench Testing Alternator
    196
  - Rotor Field Coil Current Draw
    196
  - Exploded View of Alternator
    197
  - Checking Field Coil Current Draw
    197
  - Testing Field Circuit
    197
  - Testing of Rectifier Assemblies
    198
  - Testing of Positive Rectifiers Using C-3829 Tester
    198
  - Testing Positive/Negative Rectifiers with C-3829 Tester
    199
  - Rectifier End Shield and Stator Assembly
    199
  - Testing of Rectifier Assemblies Using Test Lamp
    200
  - Testing Positive/Negative Rectifiers with Test Lamp
    201
  - Removal of Rectifier and Heatsink Assembly
    202
  - Rectifier End Shield Assembly
    202
  - Testing Stator
    203
  - Removal of Pulley and Bearing
    203
  - Testing of Rotor
    204
  - Removal of Bearing
    204
  - Removal of Rectifier End Shield Bearing
    204
  - Slip Rings
    205
  - Assembly of Alternator
    205
  - Testing Rotor for Ground
    205
  - Testing Rotor for Opens or Shorts
    205
  - Installation of Grease Retainer
    206
  - Installation of Rectifier End Shield Bearing
    206
  - Installation of Drive End Shield Bearing
    206
  - Installation of Pulley
    206
  - Installation of Insulators
    208
  - Installation of Positive Rectified Assembly
    208
  - Installation of Capacitor
    208
  - Installation of Battery Output Insulator
    208
  - Installation of Negative Rectifier Assembly
    210
  - Installation of Stator
    210
  - Description of Alernator
    211
  - Disassembly of Alternator
    211
  - Exploded View of Alternator (Prestolite)
    212
  - Removal of Slip Ring End Bearing
    213
  - Removal of Rectifier
    213
  - Removal of Drive End Head
    213
  - Removal of End Head Bearing
    213
  - Inspection and Testing of Components
    214
  - Testing Rotor for Shorts
    214
  - Installation of Bearing
    216
  - Installation of Rectifier
    216
  - Terminal Assembly (Prestolite)
    216
  - Slip Ring End Bearing Assembly
    217
  - Testing Alternator
    217
  - Precautions
    218
  - Brush Installation
    218
  - Internal Wiring Diagram
    218
  - Alternator Service Tips
    219
  - Alternator Service Test Specifications
    219
  - Checking Alternator Belt Tension
    220
  - Servicing Battery
    221
  - Removal of Battery
    221
  - Installation of Battery
    222
  - Testing Battery
    222
  - Charging Battery
    222
  - Hydrometer Reading and Battery Charge Percent
    222
  - Checking Voltage Regulator
    223
  - Checking Overvoltage Relay
    224
  - External Power
    224
  - Operation of External Power Receptacle
    224
  - Electrical System Load Distribution
    225
  - Electrical System Component Loads
    225
  - Equipment/Furnishing Contents
    227
  - Flight Compartment
    228
  - Rigging Instructions - Seat Back Lock and Release
    228
  - Seat Back Lock
    228
  - Shoulder Harness Inertia Reel Adjustment
    229
  - Flight Control Contents
    231
  - Troubleshooting (Surface Controls)
    234
  - Cable Tension Vs. Ambient Temperature
    239
  - Rod End Installation Method
    240
  - Standard Procedures
    241
  - Removal of Control Column Assembly
    241
  - Control Column Assembly
    242
  - Installation of Control Column Assembly
    243
  - Aileron and Tab
    244
  - Removal of Aileron Control Cables
    244
  - Aileron Controls
    245
  - Installation of Aileron Control Cables
    246
  - Removal of Aileron Bellcrank Assembly
    247
  - Installation of Aileron Bellcrank Assembly
    247
  - Rigging and Adjustment of Aileron Controls
    248
  - Aileron Rigging
    249
  - Bellcrank Rigging Tool
    249
  - Aileron Rigging Tool
    250
  - Rudder and Tab
    251
  - Removal of Rudder and Steering Pedal Assembly
    251
  - Rudder and Steering Pedal Assembly
    252
  - Installation and Rudder and Steering Pedal Assembly
    253
  - Rudder Controls
    254
  - Rudder Rigging Tool
    255
  - Clamping Rudder Pedals
    255
  - Rudder Rigging
    255
  - Removal of Rudder Control Cables
    256
  - Installation of Rudder Control Cables
    256
  - Rigging and Adjustment of Rudder Controls
    257
  - Removal of Rudder Trim Controls
    257
  - Stabilator and Tab
    258
  - Installation of Rudder Trim Controls
    258
  - Rigging and Adjustment of Rudder Trim Controls
    258
  - Removal of Stabilator Control Cables
    258
  - Rudder Travel Adjustments
    259
  - Rudder Trim Control
    259
  - Installation of Stabilator Control Cables
    260
  - Stabilator Controls
    261
  - Stabilator and Stabilator Trim Travel Adjustments
    262
  - Stabilator Rigging Tool
    262
  - Rigging and Adjustment of Stabilator Controls
    263
  - Removal of Stabilator Trim Assembly
    264
  - Installation of Stabilator Trim Assembly
    265
  - Methods of Securing Trim Cables
    265
  - Stabilator Trim Control
    266
  - Rigging and Adjustment of Stabilator Trim
    268
  - Flaps
    269
  - Removal of Wing Flap Controls
    269
  - Flap Controls
    270
  - Installation of Wing Flap Controls
    271
  - Flap Rigging Tool
    272
  - Rigging and Adjustment of Wing Flaps
    273
  - Stall Warning Horn, Indicator and Detector
    274
  - Removal of Lift Detector
    274
  - Installation of Lift Detector
    274
  - Adjustment of Lift Detector
    274
  - Flap Rigging
    275
  - Aerofiche Explanation and Reversion Status Contents
    281
  - Gama System/Chapter Index Guide
    283
- Three View 1B17
  285
- Station References 1B18
  285
- Access Plates and Panels 1B19
  285
- Jacking Arrangement 1B23
  285
- Weighing Airplane 1C4
  285
- Leveling Longitudinally 1C5
  285
- Leveling Laterally 1C5
  285
- Placards and Decals 1C17
  285
- Fuel Filter Bowl and Screen 1C22
  285
- Servicing Points 1D2
  285
  - Fuel Contents
    294
  - Fuel System Diagram
    296
  - Troubleshooting (Fuel System)
    297
  - Disassembly/Assembly of Locking Fuel Cap
    299
  - Inspection and Repair of Fuel Tank
    299
  - Installation of Fuel Tank
    299
  - Removal of Fuel Tank
    299
  - Distribution
    300
  - Locking Fuel Cap Assembly
    300
  - Removal Fuel Selector Valve
    300
  - Cleaning and Inspection of Filter Bowl Screen
    301
  - Installation of Fuel Selector Valve
    301
  - Removal of Electric Fuel Pump
    301
  - Removal/Installation of Fuel Filter Bowl and Screen
    301
  - Plunger Fuel Pump
    302
  - Cleaning, Inspection and Repair of Electric Fuel Pump
    303
  - Dissembly of Electric Fuel Pump
    303
  - Resistance Check
    303
  - Adjustment of Electric Fuel Pump
    304
  - Assembly of Fuel Pump
    304
  - Inspection and Tightening of Fuel Line Union Fittings
    305
  - Installation of Electric Fuel Pump
    305
  - Lines and Fittings
    305
  - Replacement of Fittings
    306
  - Tolerances, Union Nut and Tubing Nut
    306
  - Indicating
    307
  - Installation of Fuel Quantity Transmitter Unit
    307
  - Removal of Fuel Quantity Transmitter Unit
    307
  - Fuel Quantity Sender/Gauge Check
    308
  - Fuel Gauge
    309
  - Transmitter/Fuel Gauge Tolerances
    309
  - Landing Gear Contents
    311
  - Troubleshooting (Landing Gear)
    314
  - Cleaning, Inspection and Repair of Main Gear Oleo
    316
  - Disassembly of Main Gear Oleo
    316
  - Main Gear Oleo Strut Assembly
    317
  - Assembly of Main Gear Oleo
    318
  - Removal of Main Landing Gear
    318
  - Main Gear Installation
    319
  - Cleaning, Inspection and Repair of Main Landing Gear
    320
  - Disassembly of Nose Gear Oleo
    320
  - Installation of Main Landing Gear
    320
  - Nose Gear Oleo Strut Assembly
    321
  - Cleaning, Inspection and Repair of Nose Gear Oleo
    322
  - Assembly of Nose Gear Oleo
    323
  - Nose Gear Oil Orifice Retainer Ring Installation
    323
  - Cleaning, Inspection and Repair of Nose Landing Gear
    324
  - Installation of Nose Landing Gear
    324
  - Nose Landing Gear Assembly
    324
  - Removal of Nose Landing Gear
    324
  - Nose Gear Installation
    325
  - Alignment of Nose Gear
    326
  - Nose Gear Alignment Tolerances
    326
  - Clamping Rudder Pedals in Neutral Position
    327
  - Removal and Disassembly of Main Wheel Assembly
    327
  - Rudder Pedals at Neutral Angle
    327
  - Wheels and Brakes
    327
  - Main Wheel Assembly
    328
  - Assembly and Installation of Main Wheel
    329
  - Inspection of Main Wheel Assembly
    329
  - Removal and Disassembly of Nose Wheel Assembly
    329
  - Nose Wheel Assembly
    330
  - Assembly and Installation of Nose Wheel Assembly
    331
  - Brake Adjustment and Lining Tolerance
    331
  - Inspection of Nose Wheel Assembly
    331
  - Removal and Disassembly of Brake Assembly
    331
  - Cleaning, Inspection and Repair of Brake Assembly
    332
  - Standard Brake Assembly
    332
  - Heavy Duty Wheel Brake Assembly
    333
  - Removal and Installation of Anchor Bolts
    334
  - Brake Disc Minimum Thickness
    335
  - Brake System Installation
    335
  - Assembly and Installation of Brake Assembly
    336
  - Disassembly of Master Cylinder
    336
  - Removal of Master Cylinder
    336
  - Assembly of Master Cylinder
    337
  - Brake Master Cylinder
    337
  - Cleaning, Inspection and Repair of Master Cylinder
    337
  - Disassembly of Brake Cylinder
    338
  - Installation of Master Cylinder
    338
  - Removal of Brake Cylinder
    338
  - Toe Brake Installation
    339
  - Brake Cylinder
    340
  - Assembly of Brake Cylinder
    341
  - Brake Bleeding Procedure
    341
  - Cleaning, Inspection and Repair of Brake Cylinder
    341
  - Installation of Brake Cylinder
    341
  - Bleeding of the Brakes after a Unit Has Been Changed
    343
  - Brake System Leak Check
    343
  - Lights Contents
    345
  - Troubleshooting (Electrical System)
    347
  - Annunciator Panel
    349
  - Installation of Dimmer Control Assembly
    349
  - Instrument Panel Lights
    349
  - Removal of Dimmer Control Assembly
    349
  - Exterior
    350
  - Removal and Installation of Landing Light
    350
  - Anti-Collision Light
    351
  - Removal/Installation of Rotating Beacon
    351
  - Removal/Installation of Wing Tip Strobe Light
    351
  - Strobe Light Connections
    352
  - Installation of Strobe Power Supply
    353
  - Removal of Strobe Power Supply
    353
  - Troubleshooting Procedure
    353
  - Navigation and Pitot/Static Contents
    356
  - Removal and Installation of Face Mounted Instruments
    357
  - Gyro Fitting Installation Procedure
    358
  - Pitot/Static System
    359
  - Rate of Climb Indicator
    360
  - Removal and Replacement of Cluster Mounted Instruments
    360
  - Troubleshooting (Rate of Climb Indicator)
    360
  - Sensitive Altimeter
    361
  - Troubleshooting (Altimeter)
    362
  - Airspeed Indicator
    363
  - Troubleshooting (Airspeed Tubes and Indicator)
    363
  - Air Driven Attitude Horizon
    364
  - Gyro Horizon
    364
  - Directional Gyro - Air Driven/Electric
    365
  - Air Driven Directional Gyro
    366
  - Electrically Driven Directional Gyro
    366
  - Adjustment of Compass
    367
  - Magnetic Compass
    367
  - Troubleshooting (Magnetic Compass)
    367
  - Turn and Bank/Pictorial Rate Instruments
    368
  - Vacuum Contents
    374
  - Troubleshooting (Vacuum System)
    375
  - Vacuum System Service Tips
    378
  - Removal of Vacuum Pump
    379
  - Installation of Vacuum Pump
    380
  - Replacing Pump Fittings
    380
  - Adjustment of Vacuum Regulator Valve
    381
  - Removal and Replacement of Regulator Valve
    381
  - Vacuum Regulator Valve
    381
  - Installation of Vacuum Sensor
    382
  - Removal of Vacuum Sensor
    382
  - Vacuum Gauge
    382
  - Auxiliary Vacuum Pump
    383
  - Auxiliary Vacuum Pump, Engine off Operational Check
    383
  - Auxiliary Vacuum Pump Installation
    384
  - Removal of Auxiliary Pump
    385
  - Installation of Auxiliary Vacuum Pump
    386
  - Electronic/Electronic Panels and Multipurpose Parts Contents
    389
  - Electrical Switches and Circuit Breakers
    390
  - Multipurpose Electrical and Electronic Parts
    390
  - Removal of Electrical Switches
    390
  - Structures Contents
    392
  - Baggage Compartment Inspection Hole and Cover Plate
    393
  - Structural Repairs
    393
  - Fiberglass Repairs
    394
  - Skin Materials and Thickness
    395
  - Baggage Compartment Inspection Holes Cutout Details
    397
  - Fiberglass Fracture and Patch Repairs
    398
  - Fiberglass Touch-Up and Surface Repairs
    398
  - Thermoplastic Repairs
    399
  - List of Materials (Thermoplastic Repair)
    400
  - Surface Scratches, Abrasions or Ground-In-Dirt
    401
  - Deep Scratches, Shallow Nicks and Small Holes
    402
  - Mixing of Epoxy Patching Compound
    402
  - Repairing of Cracks
    404
  - Welding Repair Method
    404
  - Various Repairs
    405
  - Product Listing for Liquid Safety Walk Compound
    406
  - Safety Walk Repair
    406
  - Surface Preparation
    406
  - Repair of Impacted Damage
    407
  - Repair of Stress Lines
    407
  - Application of Liquid Safety Walk Compound
    408
  - Application of Pressure Sensitive Safety Walk
    408
  - Surface Preparation for Pressure Sensitive Safety Walk
    408
  - Doors Contents
    410
  - Adjustment of Door
    411
  - Cabin Door
    411
  - Removal of Door Latch Mechanism
    411
  - Removal/Installation of Door
    411
  - Installation/Adjustment of Door Latch Mechanism
    412
  - Removal/Installation of Door Lock Assembly
    412
  - Removal/Installation of Door Safety Latch
    412
  - Adjustment of Door Safety Latch
    413
  - Removal and Installation of Door Snubber
    413
  - Door Snubber Installation
    415
  - Removal/Installation of Baggage Door
    416
  - Removal/Installation of Baggage Door Hinge
    416
  - Removal/Installation of Baggage Door Lock Assembly
    416
  - Stabilizers Contents
    418
  - Installation of Stabilator
    419
  - Removal of Stabilator
    419
  - Checking Stabilator Surfaces Free Play
    420
  - Installation of Stabilator Trim Tab
    420
  - Removal of Stabilator Trim Tab
    420
  - Empennage Group Installation
    421
  - Methods of Securing Control Cables
    422
  - Stabilator Balance
    422
  - Balancing Equipment
    423
  - Balancing Stabilator
    423
  - Removal of Vertical Fin
    423
  - Vertical Stabilizer
    423
  - Installation of Rudder
    424
  - Installation of Vertical Fin
    424
  - Removal of Rudder
    424
  - Balancing Rudder
    425
  - Windows Contents
    428
  - Cabin
    429
  - Installation of Windshield
    429
  - Removal of Side Windows
    429
  - Removal of Windshield
    429
  - Windshield Installation
    430
  - Installation of Side Windows
    431
  - Side Window Installation, Single Pane
    431
  - Wings Contents
    433
  - Auxiliary Structure
    434
  - Installation of Wing Tip
    434
  - Removal of Wing Tip
    434
  - Repair of Wing Tip
    434
  - Wing Installation
    435
  - Removal of Wing
    438
  - Wing to Fuselage Attach Fittings
    438
  - Installation of Wing
    439
  - Aileron and Flap Installation
    440
  - Flight Surfaces
    442
  - Removal of Aileron
    442
  - Balancing Aileron
    443
  - Balancing Equipment and Procedure
    443
  - Checking Aileron Free Play
    443
  - Installation of Aileron
    443
  - Aileron Balance Configuration
    444
  - Installation of Wing Flap
    445
  - Removal of Wing Flap
    445
  - Propeller Contents
    447
  - Maintenance of Propeller
    448
  - Propeller Assembly
    448
  - Removal of Propeller
    448
  - Typical Nicks and Removal Method
    448
  - Cleaning, Inspection and Repair of Propeller
    449
  - Installation of Propeller
    449
  - Propeller Installation
    450
  - Checking Propeller Blade Track
    451
  - Controlling
    451
  - Propeller Torque Limits
    451
  - Removal/Installation of Propeller Governor
    451
  - Propeller Governor
    452
  - Rigging and Adjustment of Propeller Governor
    452
  - Standard Practices - Engine Contents
    455
  - Power Plant Contents
    459
  - Troubleshooting (Engine)
    461
  - Pre-Oiling Engine
    467
  - Removal of Engine
    467
  - Installation of Engine
    468
  - Engine Installation
    469
  - Engine Mount Assembly
    470
  - Cowling Installation
    471
  - Maintenance of Cowling
    471
  - Removal of Cowling
    471
  - Air Intakes
    472
  - Cleaning, Inspection and Repair of Cowling
    472
  - Installation of Cowling
    472
  - Replacement of Engine Shock Mounts
    472
  - Carburetor Ice Detection System
    473
  - Functional Check of Ice Detector Probe
    474
  - Installation of Ice Detector Probe
    474
  - Removal of Ice Detector Probe
    474
  - Carburetor Ice Detector Probe Installation
    475
  - Carburetor Ice Detection System Test
    476
  - Installation of Carburetor Airbox
    477
  - Rear View of Carburetor Airbox
    477
  - Removal of Carburetor Airbox
    477
  - Engine Fuel System Contents
    479
  - Carburetor Maintenance
    480
  - Throttle Arm
    480
- Adjustment of Idle Mixture
  480
Chapter 73 - Engine Fuel System

480
- General
  480
- Distribution
  480
  - Adjustment of Idle Speed
    481
  - Carburetor
    481
  - Disassembly, Cleaning and Assembly of Engine Primer
    482
  - Engine Primer
    482
  - Removal of Engine Primer
    482
  - Adjustment of Throttle and Mixture Controls
    483
  - Controlling
    483
  - Installation of Engine Primer
    483
  - Primer Jets
    483
  - Adjustment of Engine Controls
    484
  - Fuel Pressure Gauge
    484
  - Indicating
    484
  - Troubleshooting (Fuel Pressure Gauge)
    485
  - Ignition Contents
    487
  - Electrical Power Supply
    491
  - Inspection of Magneto
    491
  - Height of Spring in Distributor Block Tower
    492
  - Contact Points
    492
  - Installation and Timing (Magneto to Engine)
    493
  - Engine Timing Marks
    494
  - Timing Light Connected to Magneto
    494
  - Timing Marks on Magneto Rotor
    496
  - Painted Tooth Centered in Timing Window
    496
  - Timing Mark on Rotor Aligned with Pointer
    496
  - Internal Timing of Magneto
    497
  - Timing Light Connected to Magneto and Breakers
    497
  - Cam End View of Magneto
    499
  - Removal of Impulse Coupling
    500
  - Inspection of Impulse Coupling
    500
  - Removing Impulse Coupling
    501
  - Checking Flyweight to Stop Pin Clearance
    501
  - Stop Pin Installation Dimension
    501
  - Checking Flyweight Axial Wear with Drill Shank
    502
  - Checking Flyweight Radial Wear with Gauge
    502
  - Points of Coupling Body Wear
    503
  - Acceptable and Deformed Coupling Springs
    503
  - Installation of Impulse Coupling
    504
  - Checking Impulse Coupling for Magnetization
    505
  - Orientation of Spring in Coupling Body
    505
  - Lifting Inner End of Spring
    505
  - Ignition Harness
    506
  - Inspection of Harness
    506
  - Checking Harness Lead Continuity
    507
  - Checking Harness Lead Lnsulation Resistance
    507
  - Modified Pliers
    507
  - Removing Spring from Lead Assembly
    507
  - Maintenance of Harness
    508
  - Assembly Tool
    509
  - Using Assembly Tool
    509
  - Ferrule Positioned under Braid
    510
  - Ferrule Seating Tool
    510
  - Position of L 1-8627 Kit and Contact Spring at Start of Installation
    511
  - Position of 11-8627 Kit and Contact Spring after Installation
    511
  - Lubricating Sleeve
    511
  - Lubricating Ferrule Shoulder
    511
  - Coupling Troques
    512
  - Removal of Spark Plugs
    513
  - Removing Spark Plug Frozen to Bushing
    513
  - Inspection and Cleaning of Spark Plugs
    514
  - Installation of Spark Plugs
    515
  - Removal of Ignition Switch
    515
  - Installation of Ignition Switch
    515
  - Ignition Switch Wire Positions
    516
  - Engine Indicating Contents
    519
  - Power
    520
  - Manifold Pressure Gauge
    520
  - Troubleshooting (Manifold Pressure Indicator)
    520
  - Tachometer Indicator
    521
  - Troubleshooting Tachometer
    521
  - Engine Oil Pressure Gauge
    522
  - Temperature
    522
  - Oil Temperature Indicator
    522
  - Troubleshooting (Engine Oil Pressure Gauge)
    522
  - Exhaust Gas Temperature Gauge
    523
  - Removal of EGT Probe and Gauge
    523
  - Cleaning and Inspection of EGT Gauge
    523
  - Troubleshooting (Oil Temperature Indicators)
    523
  - Installation of EGT Probe and Gauge
    524
  - Cylinder Head Temperature Gauge
    524
  - Troubleshooting (Exhaust Gas Temperature Gauge)
    524
  - Troubleshooting (Cylinder Head Temperature Gauge)
    525
  - Exhaust Contents
    527
  - Inspection of Exhaust System
    528
  - Exhaust System Inspection Points
    528
  - Oil System Contents
    531
  - Removal of Oil Cooler
    532
  - Installation of Oil Cooler
    532
  - Removal of Oil Pressure Sensor
    532
  - Installation of Oil Pressure Sensor
    533
  - Starting Contents
    536
  - Troubleshooting (Starter)
    538
  - Cranking
    540
  - Maintenance of Starting System
    540
  - Exploded View of Gear Reduction Starting Motor
    540
  - Overhaul of Starting Motor
    541
  - Removal of Starting Motor
    541
  - Disassembly of Starting Motor
    541
  - Brushes
    541
  - Turning Starting Motor Commutator
    542
  - Testing Motor Armature for Shorts
    542
  - Testing Motor Fields for Grounds
    542
  - Armature
    543
  - Field Coils
    543
  - Brush Holders
    543
  - Bendix Drive
    543
  - Assembly of Starting Motor
    544
  - No-Load Test Hook-Up
    544
  - Stall-Torque Hook-Up
    544
  - Bench Test
    545
  - Starting Motor Control Circuit
    545
  - Starting Motor Service Test Specification
    546
  - External Power Receptacle
    546
- Lubrication Chart (Air Conditioning Condenser) 1D22
  556
  - List of Charts
    562
  - Charts and Wiring Diagrams Contents
    565
  - Torque Requirements
    566
  - Flare Fitting Torques
    566
  - Recommended Nut Torques
    567
  - General Requirements
    567
  - Conversion Tables
    570
  - Decimal Conversions
    571
  - Centigrade - Farenheit Conversion Table
    573
  - Decimal Equivalents of Drill Sizes
    575
  - List of Consumable Materials
    576
  - Vendor Information
    582
  - Electrical Schematics
    584
  - Electrical Wire Coding
    584
  - Electrical Symbols
    585
  - Electrical Schematic Index
    586
  - Annunciator (Early Models)
    589
  - Annunciator (Later Models)
    590
  - Alternator (Early Models)
    591
  - Alternator (Later Models)
    592
  - Starters
    593
  - Air Conditioning/Air Blower
    594
  - Avionics Bus (with Master, Emergency Switches)
    595
  - Pitot Heat
    595
  - Fuel Pump
    595
  - Digital and Electrical Clock and Hourmeter
    596
  - Engine Gauges
    596
  - Alternate Turn and Bank
    597
  - Turn and Bank
    597
  - Anti-Collision - Wing Strobes
    598
  - Anti-Collision Beacon and Wing Strobes
    598
  - Anti-Collision - Beacon
    599
  - Recognition Light
    599
  - Landing Light
    599
  - Position
    599
  - Cabin, Dome and Cigar Lighter
    600
  - Panel Lighting (Early Models)
    600
  - Panel Lighting (Later Models)
    601
  - Radio Panel Lighting
    602
  - Stall Warning
    602
  - Special Purpose Equipment Contents
    605
  - Tools and Test Equipment
    606
  - Tire Balancer Building Instructions
    607
  - Tire Balancer Fixture
    607
  - Control Surface Balancing Tool
    608
  - Orifice Replacement Tool
    609
  - Fabricated Tool for Baggage Door Lock
    610
  - Retainer Ring Tool
    610
  - Fabricated Aileron Bellcrank Rigging Tool
    611
  - Fabricated Rudder Rigging Tool
    611
  - Fabricated Aileron and Flap Rigging Tool
    612
  - Fabricated Stabilator Rigging Tool
    613

Advertisement

Piper PA-28-236 DAKOTA Pilot Operating Handbook

Piper PA-28-236 DAKOTA Pilot Operating Handbook (367 pages)

Brand: Piper | Category: Aircrafts | Size: 8.3 MB

Table of Contents

General

26
- Rev.
  8
- Rev.
  9
- Revised Item
  10
- Report: Vb
  11
- Rev. 4 (Cont)
  13
- Report: Vb
  16
- Rev.
  17
- Report: Vb
  18
- Table of Contents
  26
- Introduction
  28
- Engine
  30
- Propeller
  30
- Fuel
  30
- Oil
  31
- Maximum Weights
  31
- Standard Airplane Weights
  31
- Baggage Space
  31
- Specific Loadings
  32
- Symbols, Abbreviations and Terminology
  33
Limitations

40
- Airspeed Limitations
  42
- General
  42
- Airspeed Indicator Markings
  43
- Power Plant Limitations
  43
- Power Plant Instrument Markings
  44
- Weight Limits
  44
- Center of Gravity Limits
  45
- Flight Maneuvering Load Factors
  45
- Maneuver Limits
  45
- Types of Operations
  45
- Fuel Limitations
  46
- Noise Level
  46
- Placards
  46
Table of Contents

50
- Paragraph Page
  51
- General
  52
- Emergency Procedures Checklist
  53
  - Speeds
    53
  - Engine Inoperative Procedures
    53
  - Fire
    55
  - Loss of Oil Pressure
    56
  - Loss of Fuel Pressure
    56
  - High Oil Temperature
    56
  - Electrical Failures
    56
  - Electrical Overload
    57
  - Spin Recovery
    58
  - Open Door
    58
  - Carburetor Icing
    58
  - Engine Roughness
    59
  - Propeller Overspeed
    59
- Amplified Emergency Procedures (General)
  60
- Fire
  62
  - Engine Fire During Start
    62
  - Fire in Flight
    63
- Loss of Fuel Pressure
  64
  - Installation
    64
- Loss of Oil Pressure
  64
- Electrical Failures
  65
- Electrical Overload
  65
- Open Door
  66
- Spin Recovery
  66
- Carburetor Icing
  67
- Engine Roughness
  67
- Propeller Overspeed
  68
This Page Intentionally Left Blank

70
- Airspeeds for Safe Operations
  72
- General
  72
- Normal Procedures Checklist
  74
  - Preflight Check
    74
  - Before Starting Engine
    76
  - Starting Engine When Cold
    77
  - Starting Engine When Hot
    77
  - Starting Engine When Flooded
    77
  - Starting with External Power
    77
  - Warm-Up
    78
  - Taxiing
    78
  - Ground Check
    78
  - Before Takeoff
    79
  - Takeoff
    79
  - Climb
    80
  - Cruising
    80
  - Descent
    81
  - Approach and Landing
    81
  - Stopping Engine
    81
  - Parking
    82
- Amplified Normal Procedures (General)
  84
- Preflight Check
  84
- Before Starting Engine
  87
- Starting Engine
  87
- Taxiing
  89
- Warm-Up
  89
- Ground Check
  90
- Before Takeoff
  91
- Takeoff
  92
- Climb
  93
- Cruising
  93
- Approach and Landing
  95
- Descent
  95
- Stopping Engine
  96
- Parking
  97
- Stalls
  97
- Turbulent Air Operation
  98
- Weight and Balance
  98
Performance

110
- Airspeed Calibration
  112
- Fuel, Time and Distance to Climb
  119
- Power Setting Table
  120
- Best Power Cruise Range
  124
- Best Economy Cruise Range
  125
- Fuel, Time and Distance to Descend
  128
- Landing Distance over 50 Ft. Barrier
  130
- Landing Distance over 50 Ft. Barrier - Standard Brakes
  130
- Landing Ground Roll Standard Brakes
  131
Table of Contents

134
- General
  136
- Airplane Weighing Procedure
  137
- Weight and Balance Data and Record
  140
- Weight and Balance Determination for Flight
  144
- Instructions for Using Weight and Balance Plotter
  148
- Equipment List
  152
  - Installation
    152
  - (A) Propeller and Propeller Accessories
    153
  - (B) Engine and Engine Accessories
    155
    
    Landing Gear and Brakes
    156
  - (D) Electrical Equipment
    157
  - (E) Instruments
    158
  - (G) Propeller and Propeller Accessories
    162
    
    Propeller and Propeller Accessories (Optional Equipment)
    162
  - (H) Engine and Engine Accessories (Optional Equipment)
    162
    
    Equipment
    162
  - Heavy Duty Brakes
    163
  - Installation
    164
  - (J) Electrical Equipment (Optional Equipment)
    166
    
    Installation
    166
    
    Instruments (Optional Equipment)
    167
    
    Installation
    168
  - (M) Radio Equipment (Optional Equipment)
    178
  - (N) Miscellaneous (Optional Equipment)
    191
Table of Contents

196
- Airframe
  198
- The Airplane
  198
- Engine and Propeller
  199
- Induction System
  200
- Landing Gear
  202
- Engine Controls
  203
- Flight Controls
  206
- Fuel System
  206
- Electrical System
  209
- Instrument Panel
  213
- Vacuum System
  213
- Pitot-Static System
  215
- Heating and Ventilating System
  217
- Cabin Features
  219
- Baggage Area
  221
- Finish
  221
- Stall Warning
  221
- Emergency Locator Transmitter
  222
- Piper External Power
  222
- Air Conditioning
  227
- Carburetor Ice Detection System
  228
Table of Contents

230
- General
  232
- Airplane Inspection Periods
  233
- Preventive Maintenance
  234
- Airplane Alterations
  235
- Ground Handling
  236
- Brake Service
  239
- Landing Gear Service
  239
- Propeller Service
  241
- Fuel System
  242
- Oil Requirements
  242
- Battery Service
  245
- Tire Inflation
  245
- Cleaning
  246

Advertisement

Related Products

Piper Categories

Aircrafts Tools Toy Commercial Food Equipment

Oven

More Piper Manuals