Allen-Bradley ControlLogix System 1756-L1 User Manual page 12

Table of Contents vi
Communicate with a DeviceNet
Device
Communicate with Another
™
Controller Over a DH+
®
Route PLC-5 or SLC 500
Messages From a DH+
Communicate with Another
Controller over a DH-485 Network
Communicate Over a Remote I/O
Network
Publication 1756-UM001E-EN-P - August 2002
Chapter 16
When to Use This Procedure . . . . . . . . . . . . . . . . . . . . . . . 16-1
How to Use This Procedure. . . . . . . . . . . . . . . . . . . . . . . . 16-1
Step 1: Add the 1756-DNB Module . . . . . . . . . . . . . . . . . . 16-1
Step 2: Create Aliases . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-4
Step 3: Set the Scanner to Run Mode . . . . . . . . . . . . . . . . . 16-6
Chapter 17
When to Use This Procedure . . . . . . . . . . . . . . . . . . . . . . . 17-1
How to Use This Procedure. . . . . . . . . . . . . . . . . . . . . . . . 17-2
Network
Configure Routing Tables . . . . . . . . . . . . . . . . . . . . . . . . . 17-3
Configure a 1756-DHRIO Channel . . . . . . . . . . . . . . . . . . . 17-8
Add a 1756-DHRIO Module. . . . . . . . . . . . . . . . . . . . . . . 17-11
Enter a Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-14
Configure the Message . . . . . . . . . . . . . . . . . . . . . . . . . . 17-16
Stagger the Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-20
Access ControlLogix Data . . . . . . . . . . . . . . . . . . . . . . . . 17-20
Chapter 18
™
When to Use This Procedure . . . . . . . . . . . . . . . . . . . . . . . 18-1
™
Configure Routing Tables . . . . . . . . . . . . . . . . . . . . . . . . . 18-2
Network
Configure a PLC-5 or SLC 500 Message . . . . . . . . . . . . . . . 18-6
Chapter 19
When to Use this Procedure . . . . . . . . . . . . . . . . . . . . . . . 19-1
How to Use This Procedure. . . . . . . . . . . . . . . . . . . . . . . . 19-2
Step 1: Connect the Controller to an AIC+ . . . . . . . . . . . . . 19-3
Step 2: Configure the Serial Port . . . . . . . . . . . . . . . . . . . . 19-4
Step 3: Enter a Message. . . . . . . . . . . . . . . . . . . . . . . . . . . 19-6
Step 4: Configure the Message . . . . . . . . . . . . . . . . . . . . . . 19-8
Step 5: Check the LED. . . . . . . . . . . . . . . . . . . . . . . . . . . 19-10
Step 6: Stagger the Messages . . . . . . . . . . . . . . . . . . . . . . 19-10
Chapter 20
When to Use This Procedure . . . . . . . . . . . . . . . . . . . . . . . 20-1
How to Use This Procedure. . . . . . . . . . . . . . . . . . . . . . . . 20-2
Add a 1756-DHRIO Module. . . . . . . . . . . . . . . . . . . . . . . . 20-3
Add a Remote I/O Adapter . . . . . . . . . . . . . . . . . . . . . . . . 20-6
Add a Block Transfer Module . . . . . . . . . . . . . . . . . . . . . . 20-9
Read or Write Data To or From a Block Transfer Module . 20-10
Read Data From a Block Transfer Module . . . . . . . . . . 20-11
Write Configuration or Output Data To a Block Transfer
Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-13
Configure the Messages . . . . . . . . . . . . . . . . . . . . . . . 20-14