Endress+Hauser Mycom S CPM 153 Operating Instructions Manual page 125

Mycom S CPM 153
CAL
Sensor mode pH:
Data input:
Window info calibra-
tion type Zero point 1
(selected in:PARAM\
Set up 1\Calibration\
07.00pH
:
Manual calibration)
Cal with Enter
(-2.00...16.00pH)
spec. Buffer:
Edit Buffer temp..
for Cal with Manual
(only MTC)
Buffer:
025.0°C
(-20.0...150.0°C)
Electrode condition
(only 2-circuit)
Electrode 2
good
Edit Buffer temp..
For Calibration with
(only MTC)
Buffer Table /
025.0°C
Auto Buffer recogn.
(-20.0...150.0°C)
Electrode condition
(El. 2 only 2-circuit)
Electrode 1/ 2
good
Sensor mode Redox abs. (mV):
Window info calibra- Enter Offset 1
tion type
(selected in:PARAM\
Set up 1\Calibration\
0000mV
:
Manual calibration)
for Calibration with
(-1500...1500.0mV)
Enter Data abs.:
Note: Start
For Calibration with
1st Buffer
Calibration abs.:
Submerse Electrode
in Buffer
Sensor mode Redox rel. (%):
Window i nfo calibra-
tion type
(selected in:PARAM\
Set up 1\Calibration\
:
Manual calibration)
(for Calibration with
Enter Data abs. and
with Calibration abs.
Note: Start
see above)
1st Buffer
for Calibration with
Submerse Electrode
Calibration rel.:
in Buffer
Enter Cal. points K1
1:0...30%: 20%
1: Voltage: 0600 mV
2: 70...100%: 80%
For Calibration with
2: Voltage: -0600mV
Enter Data rel.:
Note: Start
1st Buffer
Calibration with
Submerse Electrode
50% switch point:
in Buffer
Endress+Hauser
Selection
(only 2-circuit)
Electrode 1
Electrode 2
Electrode 1+2
Abort Calibration
Data input: Edit Slope 1
Zero point 2
(only 2-circuit)
07.00pH
57.19mV/pH
(-2.00...16.00pH)
(5.00...99.00mV/pH)
Note: Start Edit Buffer 1
1st buffer Temp: 25.0°C
Immerse electrode 07.00 pH
in buffer 1
(–2.00...16.00pH)
Note:
Calibration
Calibration result
invalid-->
Accept
Discharge Discharge
New Calibration New Calibration
Note: Start
Stability check
1st Buffer
Buffer 1
Immerse electrode
If stable:
in buffer 1
press E
Note: Calibration
Calibration result
invalid-->
Accept
Discharge
Discharge
New Calibration New Calibration
Enter Offset 2 Calibration
(only 2-circuit)
Accept
0000mV
Discharge
New Calibration
(-1500...1500.0mV)
Enter Buffer
Stability check
Buffer 1
0225mV
If stable:
(-1500...1500mV)
press E
Enter Buffer
Stability check
Buffer 1
10%
If stable:
(0...30%)
press E
Enter Cal. points K1 Note:
(only 2-circuit)
1:0...30%: 20%
Electrode
1: Voltage: 0600 mV
submersed?
2: 70...100%: 80%
2: Voltage: -0600mV
Stability check Calibration info
Buffer 1 Electrode 1
50% Voltage 225mV/pH
20 % Voltage 600mV/pH
If stable:
8 0% Voltage- 600mV/pH
press E
Edit Slope 2 Calibration
(only 2-circuit)
Accept
57.19mV/pH
discharge
Repeat calibration
(5.00...99.00mV/pH)
Note: Start
Stability check
2nd Buffer
Buffer 1
Immerse electrode
If stable:
in buffer 2
press E
Note:
Electrode
submersed?
Note: Start
Stability check
2nd Buffer
Buffer 2
Immerse electrode
If stable:
in buffer 2
press E
Note:
Electrode
submersed?
Note:
Electrode
submersed?
Calibration info Calibration info
Electrode 1 Electrode 2
Offset 0000mV Offset 0000mV
good good
Note: Start Enter Buffer 2
2st Buffer
10%
Submerse Electrode
in Buffer (0...30%)
Calibration
Calibration info
Electrode 2
Accept
50% Voltage 225mV/pH
20% Voltage 600mV/pH
Discharge
80% Voltage- 600mV/pH
New Calibration
Note:
Electrode
submersed?
Edit Buffer 2
Stability check
Temp: 25.0°C
Buffer 2
07.00 pH
If stable:
press E
(–2.00...16.00pH)
Identified Buffers: Electrode 1 Info:
(or calibration end) Zero point
Buffer 1:
Condition
Buffer 2:
Slope
Buffertype:E+H
Condition
Note:
Calibration
Calibration result
Accept
not valid
Discharge
New Calibration
Stability check Note:
Buffer 2 voltage range
too small
If stable:
press E
Note:
Electrode
submersed?
If you press the MEAS
key, a message will
appear asking if you
= Code entry required
want to abort the
calibration.
11 Appendix
Electrode condition
Electrode 1
good
Electrode 2 Info:
Zero point
Condition
Slope
Condition
Note:
Electrode
submersed?
Note:
Electrode
submersed?
125