Analog Output Object Instance Summary; Analog Value Object Instance Summary - Daikin MD5 Operation Manual

Analog Output Object Instance Summary

The following table summarizes the Analog Output Objects supported:
Table 41: Analog Output Objects
Instance ID Object Name
AO0 AO 1 COMMAND
AO1 AO 2 COMMAND
NOTE: For Present Value Access Types, R = Read-only,
W = Writeable, C = Commandable . Commandable
values support priority arrays & relinquish defaults .

Analog Value Object Instance Summary

The following table summarizes the Analog Value Objects supported:
Table 42: Analog Value Objects
Instance
Object Name
ID
AV0 OUTPUT SPEED This object indicates the calculated motor speed in RPM . The corresponding drive parameter is 0102 .
This object indicates the output frequency applied to the motor in Hz . The corresponding drive
AV1 OUTPUT FREQ
parameter is 0103 .
AV2 DC BUS VOLT This object indicates the drive's DC bus voltage level . The corresponding drive parameter is 0107 .
This object indicates the AC output voltage applied to the motor . The corresponding drive parameter is
AV3 OUTPUT VOLT
0109 .
AV4 CURRENT This object indicates the measured output current . The corresponding drive parameter is 0104 .
This object indicates the calculated motor output torque as a percentage of nominal torque . The
AV5 TORQUE
corresponding drive parameter is 0105 .
AV6 POWER This object indicates the measured output power in kW . The corresponding drive parameter is 0106 .
This object indicates the measured heatsink temperature in °C . The corresponding drive parameter is
AV7 DRIVE TEMP
0110 .
This object indicates, in kW hours, the drive's accumulated energy usage since the last reset . The
AV8 KWH (R)
value can be reset to zero . The corresponding drive parameter is 0115 .
AV9 KWH (NR) This object indicates the drive's accumulated energy usage in kW hours . The value cannot be reset .
AV10 PRC PID FBCK
This object is the Process PID feedback signal . The corresponding drive parameter is 0130 .
This object is the Process PID output signal's deviation from its setpoint . The corresponding drive
AV11 PRC PID DEV
parameter is 0132 .
AV12 EXT PID FBCK This object is the External PID feedback signal . The corresponding drive parameter is 0131 .
This object is the External PID output signal's deviation from its setpoint . The corresponding drive
AV13 EXT PID DEV
parameter is 0133 .
This object indicates, in hours, the drive's accumulated run time since the last reset . The value can be
AV14 RUN TIME (R)
reset to zero . The corresponding drive parameter is 0114 .
AV15 MOTOR TEMP This object indicates the drive's motor temperature .
AV16 INPUT REF 1 This object sets Input Reference 1 . Control requires parameter 1103 value = COMM .
This object sets either:
• Input Reference 2 . Control requires parameter 1106 value = COMM .
AV17 INPUT REF 2
• Process PID setpoint . Control requires parameter 1106 value = PID1 OUT and parameter 4010 value
= COMM .
This object indicates the most recent fault entered in the drive's fault log . The corresponding drive
AV18 LAST FLT
parameter is 0401 .
This object indicates the second most recent fault entered in the drive's fault log . The corresponding
AV19 PREV FLT 1
drive parameter is 0412 .
This object indicates the third most recent fault entered in the drive's fault log . The corresponding drive
AV20 PREV FLT 2
parameter is 0413 .
AV21 AO 1 ACT This object indicates Analog Output 1's level . The corresponding drive parameter is 0124 .
AV22 AO 2 ACT This object indicates Analog Output 2's level . The corresponding drive parameter is 0125 .
AV23 ACCEL1 TIME This object sets the Ramp1 acceleration time . The corresponding drive parameter is 2202 .
AV24 DECEL1 TIME
This object sets the Ramp1 deceleration time . The corresponding drive parameter is 2203 .
This object defines the parameter to be read or written to by the mailbox function. See BV15 and
AV25 MBOX PARAM
BV16 .
Table 42 continued: Analog Value Objects
www .DaikinApplied .com
This object controls Analog Output 1 . The corresponding drive parameter is 0135, COMM
VALUE 1 . Control requires parameter 1501 value = 135 .
This object controls Analog Output 2 . The corresponding drive parameter is 0136, COMM
VALUE 2 . Control requires parameter 1507 value = 136 .
Description
Description
61
e f
Mbedded ieldbUs
Present Value
Units
Access Type
Percent C
Percent C
Present Value
Units
Access Type
RPM R
Hertz R
Volts R
Volts R
Amps R
Percent R
Kilowatts R
°C R
kWh W
kWh R
Percent R
Percent R
Percent R
Percent R
Hours W
°C R
Percent C
Percent C
None R
None R
None R
Milliamps R
Milliamps R
Seconds W
Seconds W
None W
OM 1191 • MD5 VFD