YOKOGAWA WT3000 User Manual page 65

6.4 CBCycle Group
:CBCycle:FILTer?
Function Queries all settings related to the filter for Cycle
by Cycle measurement.
Syntax :CBCycle:FILTer?
Example :CBCYCLE:FILTER? ->
:CBCYCLE:FILTER:LINE:
ELEMENT1 50.0E+03;
ELEMENT2 50.0E+03;
ELEMENT3 50.0E+03;ELEMENT4 50.0E+03
:CBCycle:FILTer:LINE?
Function Queries all settings related to the line filter for
Cycle by Cycle measurement.
Syntax :CBCycle:FILTer:LINE?
Example :CBCYCLE:FILTER:LINE? ->
:CBCYCLE:FILTER:LINE:
ELEMENT1 50.0E+03;
ELEMENT2 50.0E+03;
ELEMENT3 50.0E+03;ELEMENT4 50.0E+03
:CBCycle:FILTer[:LINE][:ALL]
Function Collectively sets the line filters of all elements
for Cycle by Cycle measurement
Syntax :CBCycle:FILTer[:LINE][:ALL] {OFF|
<frequency>}
OFF = Line filter OFF
<frequency> = 500 Hz, 5.5 kHz, 50 kHz (line
filter ON, cutoff frequency)
Example :CBCYCLE:FILTER:LINE:ALL 50KHZ
Description Does not set line filters for motor input.
:CBCycle:FILTer[:LINE]:ELEMent<x>
Function Sets the line filter of individual elements for
Cycle by Cycle measurement or queries the
current setting
Syntax :CBCycle:FILTer[:LINE]:
ELEMent<x> {OFF|<frequency>}
:CBCycle:FILTer[:LINE]:ELEMent<x>?
<x> = 1 to 4 (element)
OFF = Line filter OFF
<frequency> = 500 Hz, 5.5 kHz, 50 kHz (line
filter ON, cutoff frequency)
Example :CBCYCLE:FILTER:LINE:ELEMENT1 50KHZ
:CBCYCLE:FILTER:LINE:ELEMENT1? ->
:CBCYCLE:FILTER:LINE:
ELEMENT1 50.0E+03
6-22
:CBCycle:FILTer[:LINE]:MOTor
Function Sets the motor input line filters for Cycle by
Cycle measurement or queries the current
setting
Syntax :CBCycle:FILTer[:LINE]:MOTor {OFF|
<frequency>}
:CBCycle:FILTer[:LINE]:MOTor?
OFF = Line filter OFF
<frequency> = 100 Hz, 50 kHz (line filter ON,
cutoff frequency)
Description Available only with the motor version (-MV).
:CBCycle:RESet
Function Resets Cycle by Cycle measurement.
Syntax :CBCycle:RESet
Example :CBCYCLE:RESET
:CBCycle:STARt
Function Starts Cycle by Cycle measurement.
Syntax :CBCycle:STARt
Example :CBCYCLE:START
:CBCycle:STATe?
Function Queries the Cycle by Cycle measurement
status.
Syntax :CBCycle:STATe?
Example :CBCYCLE:STATE? -> RESET
Description The contents of the response are as follows:
RESet = Reset status
STARt = Measuring
COMPlete = Measurement finished and
measured results displayed
TIMEout = Timeout
ERRFreq = Measurement finished (frequency
measurement error occurred)
:CBCycle:SYNChronize?
Function Queries all settings related to the
synchronization source for Cycle by Cycle
measurement.
Syntax :CBCycle:SYNChronize?
Example :CBCYCLE:SYNCHRONIZE? ->
:CBCYCLE:SYNCHRONIZE:SOURCE U1;
SLOPE RISE
:CBCycle:SYNChronize:SLOPe
Function Sets the slope of the synchronization source of
Cycle by Cycle measurement or queries the
current setting.
Syntax :CBCycle:SYNChronize:SLOPe {RISE|
FALL}
:CBCycle:SYNChronize:SLOPe?
Example :CBCYCLE:SYNCHRONIZE:SLOPE RISE
:CBCYCLE:SYNCHRONIZE:SLOPE? ->
:CBCYCLE:SYNCHRONIZE:SLOPE RISE
IM 760301-17E