Honeywell UDC2300 Product Manual page 8

Tables
Table 2-1 Condensed Specifications______________________________________________________ 4
Table 2-2 Preliminary Checks___________________________________________________________ 6
Table 2-3 Control Relay Contact Information ______________________________________________ 8
Table 2-4 Alarm Relay Contact Information _______________________________________________ 8
Table 2-5 Mounting Procedure _________________________________________________________ 10
Table 2-6 Permissible Wiring Bundling __________________________________________________ 12
Table 2-7 Universal Output Functionality and Restrictions ___________________________________ 12
Table 4-1 Configuration Prompt Hierarchy _______________________________________________ 24
Table 4-2 Configuration Procedure _____________________________________________________ 25
Table 4-3 TIMER Group (Numeric Code 100) Function Prompts ______________________________ 26
Table 4-4 TUNING Group (Numeric Code 200) Function Prompts ____________________________ 27
Table 4-5 SPRAMP Group (Numeric Code 300) Function Prompts ____________________________ 29
Table 4-6 ATUNE Group (Numeric Code 400) Function Prompts _____________________________ 31
Table 4-7 ALGOR Group (Numeric Code 500) Function Prompts _____________________________ 32
Table 4-8 INPUT1 Group (Numeric Code 600) Function Prompts _____________________________ 33
Table 4-9 INPUT2 Group (Numeric Code 700) Function Prompts _____________________________ 35
Table 4-10 CONTRL Group (Numeric Code 800) Function Prompts ___________________________ 36
Table 4-11 Options Group (Numeric Code 900) Function Prompts_____________________________ 38
Table 4-12 Communications Group (Numeric Code 1000) ___________________________________ 39
Table 4-13 ALARMS Group (Numeric Code 1100) Function Prompts__________________________ 41
Table 5-1 Procedure to Enter a Security Code _____________________________________________ 47
Table 5-2 Annunciators_______________________________________________________________ 49
Table 5-3 Lower Display Key Parameter Prompts __________________________________________ 50
Table 5-4 Error Messages _____________________________________________________________ 51
Table 6-1 Single Display Parameters ____________________________________________________ 55
Table 6-2 Procedure for Starting Up the Controller _________________________________________ 56
Table 6-3 Control Mode Definitions_____________________________________________________ 57
Table 6-4 Changing Control Modes (Dual Display Only) ____________________________________ 58
Table 6-5 Procedure for Changing the Local Setpoints ______________________________________ 58
Table 6-6 Procedure for Switching Between Setpoints ______________________________________ 59
Table 6-7 Procedure for Starting "TUNE" ________________________________________________ 61
Table 6-8 Procedure for Using TUNE at Start-up for Duplex Control___________________________ 62
Table 6-9 Procedure for Accessing Accutune Error Codes ___________________________________ 63
Table 6-10 Accutune Error Codes ______________________________________________________ 63
Table 6-11 Set Up Procedure __________________________________________________________ 65
Table 6-12 Procedure for Switching PID SETS from the Keyboard ____________________________ 65
Table 6-13 Procedure for Displaying Alarm Setpoints_______________________________________ 66
Table 6-14 Procedure for Displaying 3Pstep Motor Position__________________________________ 67
Table 6-15 Procedure for Setting a Failsafe Value__________________________________________ 68
Table 6-16 Procedure for Setting a Failsafe Mode __________________________________________ 69
Table 7-1 Running A Setpoint Ramp ____________________________________________________ 73
Table 7-2 Program Contents ___________________________________________________________ 75
Table 7-3 Run/Monitor Functions ______________________________________________________ 80
Table 8-1 Voltage and Resistance Equivalents for Input 1 Range Values ________________________ 84
Table 8-2 Equipment Needed __________________________________________________________ 86
Table 8-3 Set Up Wiring Procedure for Thermocouple Inputs Using an Ice Bath _________________ 87
Table 8-4 Set Up Wiring Procedure for Thermocouple Inputs using Thermocouple Source _________ 87
viii UDC2300 Controller Product Manual 12/00