Honeywell UDC 1000 Micro-Pro Manuals

Manuals and User Guides for Honeywell UDC 1000 Micro-Pro. We have 1 Honeywell UDC 1000 Micro-Pro manual available for free PDF download: Product Manual

Honeywell UDC 1000 Micro-Pro Product Manual (109 pages)

Universal Digital Controller

Brand: Honeywell | Category: Controller | Size: 12 MB

Contents
5
Introduction
11
Operator Mode
13
Initial Displays
14
Single Setpoint Operation
14
Viewing/Adjusting the Setpoint/Setpoint Ramp Rate
15
Dual Setpoint Operation
15
Alarm Status Display
16
Over-Range/Under-Range Displays
16
Sensor Break Indication
16
Manual Control Mode
17
Pre-Tune Facility
17
Self-Tune Facility
18
Viewing the Hardware Definition Code
18
Installation
19
Unpacking Procedure
19
Panel-Mounting the Controller
19
Connections and Wiring
21
Rear Terminal Connections
21
Mains (Line) Input
22
24V AC/DC Supply
22
Thermocouple Cable Colour Codes
23
Thermocouple Input
24
RTD Inputs
24
Linear Inputs
24
Dual Setpoint Selection Input
24
Relay Outputs
25
SSR Drive Outputs
25
DC Outputs
25
Serial Communications Link
25
Set up Mode
27
Entry into Set up Mode
27
Set up Mode Parameters
27
Input Filter Time Constant
30
Process Variable Offset
30
Proportional Band & Deadband/Overlap
31
Proportional Band 2
32
Reset
32
Rate
32
Overlap/Deadband
32
Setpoint Low Limit
33
Recorder Output Scale Maximum
33
Recorder Output Scale Minimum
33
Output Power Limit
33
Output 2 Cycle Time
34
Process High Alarm 1 Value
34
Band Alarm 1 Value
34
Deviation (High/Low) Alarm Value
34
Loop Alarm Enable
36
Loop Alarm Time
37
Scale Range Decimal Point
37
Scale Range Maximum
37
Scale Range Minimum
37
Manual Control Enable/Disable
38
Setpoint Strategy
38
Comunnications Enable/Disable
38
Tuning the Controller Manually
39
Controllers Fitted with Output 1 Only
39
Process Variable
40
Manual Tuning Parameters
40
Self-Tune and Pre-Tune Facilities
41
Exit from Set up Mode
41
RS485 Connections
43
Communications Enable/Disable
43
Selection of Communications Channel Address
43
Physical Requirements
43
Communications Protocol
44
Individual Parameters
48
RS485 Serial Communications
55
Read Coil Status
56
Read Holding Registers
56
Force Single Coil
57
Preset Single Register
57
Loopback Diagnostic Test
57
Preset Multiple Registers
58
Error and Exception Responses
58
CRC16 Calculation
59
Parameter Numbers
61
Bit Parameters
61
Word Parameters
62
Configuration Mode
65
Entry into Configuration Mode
65
Hardware Definition Code
66
Configuration Mode Parameters
67
Input Range
67
Communications Link Baud Rate
72
Communications Address
72
Cold Junction Compensation Enable/Disable
72
Alarm Hysteresis Outputs
73
Lock Code
73
Internal Links and Switches
75
Removing the Controller from Its Housing
75
Removing/Replacing the Output 2/Output 3 Option Pcbs
77
Removing/Replacing the RS485 Communications Option PCB or Dual Setpoint Selection Input Option PCB
77
Replacing the Controller in Its Housing
78
Selection of Input Type and Output 1 Type
78
Product Selection Guide
81
Product Specification
87
Resistance Temperaeture Detector and DC MV
88
Alphabetical Index
101

Honeywell Categories

Thermostat Controller Control Unit

Security Camera Accessories

More Honeywell Manuals

Honeywell UDC 1000 Micro-Pro Manuals

Honeywell UDC 1000 Micro-Pro Product Manual (109 pages)

Table of Contents

Related Products

Honeywell Categories