Honeywell UDC2300 Product Manual page 6

12.2.24 CSRATO (COMPUTER SETPOINT RATIO) ............................................................... 129
12.2.25 CYC T1 or CT1 X3 (CYCLE TIME - HEAT)................................................................ 129
12.2.26 CYC2T2 or CT2 X3 (CYCLE TIME2 - COOL)............................................................. 130
12.2.27 DBAND (DEADBAND) ................................................................................................. 130
12.2.28 DECMAL (DECIMAL POINT LOCATION)................................................................. 130
12.2.29 DI COM (DIGITAL INPUT COMBINATIONS) ........................................................... 131
12.2.30 DIG IN (DIGITAL INPUT)............................................................................................. 131
12.2.31 DISPLAY (SINGLE DISPLAY DEFAULT).................................................................. 133
12.2.32 EMISS (EMISSIVITY) ................................................................................................... 133
12.2.33 ENDSEG (END SEGMENT).......................................................................................... 133
12.2.34 EUHRDN (RATE DOWN VALUE)............................................................................... 133
12.2.35 EUHRUP (RATE UP VALUE)....................................................................................... 133
12.2.36 FAILSF (FAILSAFE OUTPUT VALUE)....................................................................... 134
12.2.37 FILTR1 (INPUT 1 FILTER) ........................................................................................... 134
12.2.38 FILTR2 (INPUT 2 FILTER) ........................................................................................... 134
12.2.39 FINLSP (SINGLE SETPOINT RAMP FINAL SETPOINT).......................................... 134
12.2.40 FREQ (POWER LINE FREQUENCY)........................................................................... 135
12.2.41 FSMODE ( FAILSAFE MODE) ..................................................................................... 135
12.2.42 FUZZY (FUZZY OVERSHOOT SUPPRESSION) ........................................................ 135
12.2.43 HYST (HYSTERESIS - OUTPUT RELAY ONLY) ...................................................... 135
12.2.44 I MIN or I RPM (RESET - INTEGRAL TIME).............................................................. 136
12.2.45 I2 MIN or I2 RPM (RESET2 - INTEGRAL TIME)........................................................ 136
12.2.46 INCRMT (TIME COUNT INCREMENT) ..................................................................... 136
12.2.47 IN1 HI (INPUT 1 HIGH RANGE VALUE).................................................................... 137
12.2.48 IN1 LO (INPUT 1 LOW RANGE VALUE) ................................................................... 137
12.2.49 IN1TYP (INPUT 1 ACTUATION TYPE) ...................................................................... 138
12.2.50 IN2 HI (INPUT 2 HIGH RANGE VALUE).................................................................... 139
12.2.51 IN2 LO (INPUT 2 LOW RANGE VALUE) ................................................................... 139
12.2.52 IN2TYP (INPUT 2 ACTUATION TYPE) ...................................................................... 140
12.2.53 L DISP (DISPLAY FOR TIMER OPTION) ................................................................... 140
12.2.54 LNGUAG (LANGUAGE)............................................................................................... 140
12.2.55 LOCK (LOCKOUT)........................................................................................................ 141
12.2.56 LOOPBACK (LOCAL LOOPBACK TEST).................................................................. 141
12.2.57 LSP'S (LOCAL SETPOINT SOURCE) ......................................................................... 141
12.2.58 MANRST (MANUAL RESET) ...................................................................................... 142
12.2.59 MINRPM (RESET UNITS)............................................................................................. 142
12.2.60 OUTALG (OUTPUT ALGORITHM)............................................................................. 142
12.2.61 OUT Hi (HIGH OUTPUT LIMIT).................................................................................. 143
12.2.62 OUT Lo (LOW OUTPUT LIMIT) .................................................................................. 143
12.2.63 PARITY (PARITY) ......................................................................................................... 143
12.2.64 PB or GAIN (PROPORTIONAL BAND or GAIN)........................................................ 144
12.2.65 PB 2 or GAIN 2 (PROPORTIONAL BAND 2 or GAIN 2)............................................ 144
12.2.66 PBorGN (PROPORTIONAL BAND UNITS) ................................................................ 145
12.2.67 PERIOD (TIMEOUT PERIOD) ...................................................................................... 145
12.2.68 PG END (PROGRAM TERMINATION STATE).......................................................... 145
12.2.69 PIDSET (NUMBER OF TUNING PARAMETER SETS) ............................................. 146
12.2.70 PVSTRT (PV START).................................................................................................... 147
12.2.71 PWROUT (THREE POSITION STEP CONTROL OUTPUT START-UP MODE) ..... 147
12.2.72 PWR UP (POWER UP CONTROLLER MODE RECALL) .......................................... 148
12.2.73 RATE T (RATE TIME)................................................................................................... 148
vi UDC2300 Controller Product Manual 12/00