Details Of Each Setting Items - Epson Stylus Pro 4400 Service Manual

EPSON Stylus Pro 4400/4450/4800/4880/4880C

Details of each setting items

Setting
PG setting Enter any PG position.
Cutting method Cutting method is selected when cutting paper.
Paper feed Paper feeding is adjusted. The setting value is operated
adjustment as an absolute value.
Eject paper Select eject paper roller. If auto is selected, it is operated
roller set as cut sheet: sheet Star Wheel, roll paper: none
Ink drying time Ink drying time for each pass is set. The carriage stops at
the right/left sides of paper for setting time. (DR m1 = 40h)
Paper suction Paper suction is set to make paper stable on the platen.
Select "-1" for thin paper (film etc.), which is difficult to
feed and lower the suction according to thickness rate.
MW print Micro weave mode is adjusted.
adjustment When print speed has priority, lower the setting value.
When quality has priority, raise the setting value.
Note *1: Cutting Method setting items in the driver are slightly different from that of the panel default setting. The driver settings are as follows.
:
"Cut Method" SN m1=80h(Cut Method) SN m1=81h(Cut Pressure)
:
Standard m2=00h(Printer Table)
Thin Paper :m2=02h(Half-speed star wheel)m2=49h (Duty:70%300gf)
Thick Paper,Fast :m2=01h(Standard 2 levels)m2=7Eh (Duty:125% 700gf)
Thick Paper,Slow :m2=06h(Low-speed star wheel)m2=65h (Duty:100% 500gf)
*2: EX1B command is transmitted and registered in the media table in increments of 1msec. Inputting in increments of 100 msec is available when using the panel or utility. The
setting value is displayed in increments of 100 msec rounding off fractions.
Note 1: Value set by EX 1B command is similar to the above parameters.
2: If value other than parameters above or value out of range is set by EX 1B command, set by replacing with values below.
• PG setting : Standard: m2=03h (PG Little – 1.2mm)
• Cutting method : Standard m2=03h m2=49h
• Paper feed adjustment : 0% SN
• Eject paper roller set : AUTO
Product Description
Table 1-33. Details of each setting items
Operation
• SN
• Wider m2 = 01h (PG Big: 2.1mm)
• Standardm2 = 03h (PG Little: 1.2mm)
• SN
• Standardm2 = 03h
• Thick paper, Fastm2 = 01hm2 = 7Eh
• -0.7% <= ±0% <= 0.7%SN m1 = 04h
• If -0.7%SN m2 = 1Fh
• SN
• SHEETm2 = 01h
• ROLL NOMALm2 = 03h (None)
0 sec. ~ 10000 mm/sec (unit 100mm/sec)
0000h ~ 01F4h
• SN
• -1
• -3
Refer to
print adjustment.
m2=00h(Printer Table)
m2=65h
m2=00h
Operating Panel
Setting value
m1 = 01h
m1 = 80h
*1
m2 = 65h
m1 = 85h
*2
m1 = 05h
m2 = 1Ah (50%)
m2 = 06h (10%)
Table 1-34 "MW print adjustmen List"(p75)
• Ink drying time : 0 sec.
• Paper suction : Standard m2=33h (100%)
• MW print adjustment: n2:00h
Revision C
• Widestm2 = 05h (PG Maximum: 2.6mm)
• Wide m2 = 02h (PG Middle: 1.5mm)
• Narrowm2 = 04h (PG Minimum: 0.7mm)
• SN m1 = 81h
• Thin paperm2 = 02hm2 = 49h
• Thick paper, Slowm2 = 06hm2 = 65h
• If 0% SN m2 = 65h
• If 0.7%SN m2 = ABh
• AUTO m2 = 00h
• ROLL CURLEDm2 = 02h
• Standardm2 = 33h (100%)
• -2 m2 = 10h (30%)
• -4 m2 = 04h (6%)
for MW modes that can be selected by MW
74