High-Speed High-Resolution 1 Ms/S, 16-Bit Isolation Module (701251) - YOKOGAWA DL850E User Manual

High-Speed High-Resolution 1 MS/s, 16-Bit Isolation Module (701251)

Item
Standard operating conditions
Effective measurement range
Number of input channels
Input coupling
Maximum sample rate
Input format
1
Frequency characteristics
(−3 dB point when a sine wave
of amplitude ±3 div is applied)
Voltage-axis sensitivity setting
Maximum input voltage
(at a frequency of 1 kHz or less)
Maximum allowable common
mode voltage
(at a frequency of 1 kHz or less)
Vertical (voltage) axis accuracy
DC accuracy 1
Input connector
Input impedance
−3 dB point when AC coupled
low frequency attenuation point
Common mode rejection ratio
Residual noise level
(Input section shorted)
Withstand voltage
Allowable transient surge voltage
(instantaneous)
Insulation resistance
A/D conversion resolution
Temperature coefficient
Bandwidth limit
Probe attenuation setting
IM DL850E-03EN
Specifications
Temperature: 23 ±5°C
Humidity: 20 to 80% RH
After a 30-minute warm-up and after calibration
20 div (display range: 10 div)
2
AC, DC, and GND
1 MS/s
Isolated unbalanced
5 mV/div to 20 V/div: DC to 300 kHz
2 mV/div and 1mV/div: DC to 200 kHz
1 mV/div to 20 V/div (1-2-5 steps) (when using 1:1 probe attenuation)
Combined with the 700929 (10:1), 702902 (10:1), or 701947 (100:1):
600 V (DC+ACpeak)
Combined with the 701901+701954 (1:1):
140 V (DC+ACpeak)
Direct input (cable that does not comply with the safety standards):
42 V (DC+ACpeak)
Working voltage of safety standard
In combination with 700929 (10:1)/702902 (10:1)/701947 (100:1),
5
701901+701954 (1:1):
400 Vrms (measurement category Other (O)), 300 Vrms (CAT II)
Direct input (cable that does not comply with the safety standards):
42 V (DC+ACpeak) (CAT II, 30 Vrms)
5 mV/div to 20 V/div: ±(0.25% of 10 div)
2 mV/div: ±(0.3% of 10 div)
1 mV/div: ±(0.5% of 10 div)
BNC connector (isolated type)
1 MΩ ± 1%, approx. 35 pF
1 Hz or less (0.1 Hz or less when using the 700929 or 702902, 0.01 Hz or less when using
the 701947)
80 dB (50/60 Hz) or more (typical value
±100 µV or ±0.01 div whichever is greater (typical value
1500 Vrms for 1 minute (across each terminal and earth) (60 Hz)
±2100 Vpeak (across each input terminal and earth)
500 VDC, 10 MΩ or more (across each input terminal and earth)
16 bit (2400 LSB/div)
Zero point: 5 mV/div to 20 V/div:
2 mV/div:
1 mV/div:
Gain: 1 mV/div to 20 V/div:
Select from Full, 40 kHz, 4 kHz, and 400 Hz
Cut-off characteristics: −12 dB/OCT (typical value
Voltage probe: 1:1, 10:1, 100:1, 1000:1
Current probe: 1 A:1 V, 10 A:1 V (for the 701932/701933), 100 A: 1 V (for the 701930/701931)
6.13 Module Specifications
2
4
6
3
or in combination with
7
8 )
8
)
±(0.02% of 10 div)/°C (typical value
±(0.05% of 10 div)/°C (typical value
±(0.10% of 10 div)/°C (typical value
±(0.02% of 10 div)/°C (typical value
8
)
1
2
3
4
5
6
App
Index
8
)
8
)
8
)
8 )
6-23