Table of Contents
Advertisement
3.5.3.1.3 DETERMINING WHETHER *RST COMMAND SETS THE OUTPUT OFF OR ON
The user can control whether the *RST command (see PAR. A.11) sets the output on or off.
Table 3-17 describes how the unit operates depending on how *RST set Output is config-
ured, and the load type selected.
From the power-up screen press
desired. To modify highlight Interface Settings (see Table 3-16) and press
or Off and press
out saving for power-up) and exit.
Load type when *RST
Issued (see NOTE)
• Active or Resistive Load
(see PAR. 3.3.6)
• Battery Load (see PAR.
3.3.6)
• NOTE: Prior to issuing *RST unit may be operating in either voltage mode or current mode.
3.5.3.2
RS 232 SERIAL PORT SETUP
Paragraphs 3.5.3.2.1 through 3.5.3.2.3 below describe the setup required for the BOP to com-
municate via the RS 232C Serial bus using SCPI commands.
3.5.3.2.1 SELECT BAUD RATE
To change the Baud Rate configuration press
enter the Interface menu (see Table 3-16). Highlight Baud Rate and press
Off (to disable the serial port), 9600 or 19,200 and press
power-up or
3.5.3.2.2 CONFIGURE XON/XOFF PROTOCOL
From the power-up screen press
16), highlight SERIAL XON/XOFF and press
save, then press
power-up) and exit.
Enable - Allows BOP to control when data is received (see PAR. 3.5.6.2.1 for a description of
Xon/Xoff protocol).
Disable - Disables XON/XOFF. If both Serial XON/XOFF and Prompt functions are disabled,
Echo mode is set (see PAR. 3.5.6.2.2 for a description of echo mode).
3.5.3.2.3 CONFIGURE PROMPT MODE
From the power-up screen press
16). Highlight Serial Prompt and press
BOP HIPWR 080709
%
!
to save. Press
TABLE 3-17. OPERATION OF #RST COMMAND
Internal
• Voltage mode
• Main Channel reference set to 0.0V
• Current protect set to 5% of
• Voltage protect set to 5% above
• If *RST set to ON, unit is set to Voltage Mode
• If *RST set to OFF unit is set to Current Mode
• Main Channel reference set to 0.0A
• Current protect set to 5% of
• Voltage protect set to 5% above
%
to apply the changes (without saving for power-up) and exit.
%
$
to save for power-up or
%
, and note whether "*RST set Output" setting is as
$
to save for power-up or
BOP Status After *RST Issued
• LCD shows mode is Voltage, Source
• Vset set to 0.0V
I
• ±CProt set to minimum (box) values
Onom
E
• If *RST set to OFF, output is disabled
Onom
• If *RST set to ON, output is enabled
• LCD shows mode is Voltage, Source
• Vset set to 0.0V
• ±CProt: minimum (box) values
I
• If *RST set to OFF, output is disabled
Onom
E
• If *RST set to ON, output is enabled
Onom
%
from the power-up screen, then press
!
, then press
to enter the Interface menu (see Table 3-
!
. Highlight the desired option and press
%
to apply the changes (without saving for
!
, then press
to enter the Interface menu (see Table 3-
!
, highlight the desired option and press
!
, then highlight On
%
to apply the changes (with-
Front Panel Display
!
, then highlight the
$
$
to save. Press
!
to
to save for
$
to
$
to save,
3-45
Advertisement
Table of Contents
