Table of Contents
Advertisement
TABLE
1-1
BOP 1000 Watt Model Parameters .............................................................................................................1-1
1-2
BOP General Specifications .......................................................................................................................1-2
1-3
Equipment Supplied ....................................................................................................................................1-15
1-4
Safety Symbols ...........................................................................................................................................1-15
1-5
Accessories .................................................................................................................................................1-17
2-1
Rear Panel Connector Functions ................................................................................................................2-2
2-2
IEEE 1118 Connector Input/Output Pin Assignments .................................................................................2-3
2-3
Trigger Port Pin Assignments .....................................................................................................................2-3
2-4
External Protection Connector Input/Output Pin Assignments ....................................................................2-3
2-5
RS232C PORT Input/Output Pin Assignments ...........................................................................................2-4
2-6
Parallel/Serial Control Out Port Pin Assignments .......................................................................................2-4
2-7
Parallel/Serial Control In Port Pin Assignments ..........................................................................................2-4
2-8
Parallel/Serial Protect In Port Pin Assignments ..........................................................................................2-5
2-9
Parallel/Serial Protect Out Port Pin Assignments .......................................................................................2-5
2-10
Analog I/O Port Input/Output Pin Assignments ...........................................................................................2-6
2-11
IEEE 488 Port Input/Output Pin Assignments .............................................................................................2-7
2-12
Multiple Units Menu Functions ....................................................................................................................2-20
2-13
Slave Status Message Definitions ..............................................................................................................2-22
3-1
Front Panel Controls and Indicators ...........................................................................................................3-2
3-2
Special Key Functions ................................................................................................................................3-3
3-3
Display (Operator Convenience) Menu Functions ......................................................................................3-10
3-4
Voltage and Current Parameter Definitions ................................................................................................3-13
3-5
Max/Min Settings Menu ..............................................................................................................................3-16
3-6
Power Supply Behavior when Output is set to OFF ....................................................................................3-20
3-7
Examples Showing How Power-up Settings Function ................................................................................3-21
3-8
Save/recall menu ........................................................................................................................................3-24
3-9
Sine, Triangle and Ramp Waveform Frequency vs. Points ........................................................................3-27
3-10
Square Waveform Frequency vs. Points ....................................................................................................3-27
3-11
Waveform Segment Details Menu ..............................................................................................................3-29
3-12
New Waveform Settings Menu ...................................................................................................................3-30
3-13
Error Message Explanations .......................................................................................................................3-33
3-14
Revisions/test Menu ....................................................................................................................................3-37
3-15
Analog Remote Setup Menu .......................................................................................................................3-38
3-16
Interface Settings Menu ..............................................................................................................................3-44
3-17
Operation of #RST Command ....................................................................................................................3-45
3-18
IEEE 488 (GPIB) Bus Interface Functions ..................................................................................................3-46
3-19
IEEE 488 (GPIB) Bus Command Mode Messages .....................................................................................3-47
3-20
IEEE 488 (GPIB) Bus Data Mode Messages ..............................................................................................3-47
3-21
Rules Governing Shortform Keywords ........................................................................................................3-57
4-1
Calibration Summary ..................................................................................................................................4-1
4-2
Suggested Sense Resistors ........................................................................................................................4-3
4-3
Voltage Calibration Measurements and Tolerances ...................................................................................4-4
4-4
Current Calibration Measurements and Tolerances ...................................................................................4-5
4-5
Calibration Storage ....................................................................................................................................4-16
A-1
IEEE 488.2 Command/query Index ........................................................................................................... A-1
A-2
Standard Event Status Enable Register and Standard Event Status Register Bits ................................... A-1
A-3
Service Request Enable and Status Byte Register Bits ............................................................................. A-5
A-4
Built-in test Error Codes ............................................................................................................................. A-6
B-1
SCPI Subsystem Command/query Index .................................................................................................. B-1
B-2
List Data Table ........................................................................................................................................... B-15
B-3
Operation Condition Register, Operation Enable Register,
and Operation Event Register Bits .......................................................................................................... B-28
B-4
Questionable Event Register, Questionable Condition Register
and Questionable Condition Enable Register Bits .................................................................................. B-29
B-5
Error Messages .......................................................................................................................................... B-35
BOP-1K 08709
LIST OF TABLES
TITLE
PAGE
ix
Advertisement
Table of Contents
