At Command List - Panasonic Foma p705im Instruction Manual

AT Command List

AT command
A/ Re-executes the last executed
command. No carriage return is
[M] required.
AT%V Displays the version of the
FOMA phone.
[M]
AT&Cn Selects the operating conditions
[M] of the circuit CD signal sent to
[&F][&W] the DTE.
AT&Dn Selects an operation to be
performed when the circuit ER
signal received from the DTE
transits from ON to OFF.
[M]
[&F][&W]
AT&En Selects the speed display
specification for connection.
[M]
[&F][&W]
AT&Fn Returns all registers to the
default. Performs line
disconnection processing if you
enter this command during
[AT][M] communication.
AT&Sn Specifies the control of the data
[M] set ready signal to be output to
[&F][&W] the DTE.
AT&Wn Stores the current set values.
[M]
AT¢DANTE Shows the number of antenna
bars. (0 to 3)
[AT][M]
AT¢DGANSM=n Sets the reject/accept setting
mode for the packet incoming
call.
The setting with this command is
valid for incoming calls in packet
communication after you enter
[M] the setting command.
AT¢DGAPL=n Sets the APN of which packet
[,cid] incoming call is to be accepted.
To specify the APN, use the
<cid> parameter defined in
AT+CGDCONT.
[M]
AT¢DGARL=n Sets the APN of which packet
[,cid] incoming call is to be rejected.
To specify the APN, use the
<cid> parameter defined in
+CGDCONT.
[M]
Outline
n=0: CD is always ON.
n=1: CD varies according to the carrier of the other
party's modem. (default)
n=0: Ignores the ER status. (Always assumed to be
ON.)
n=1: Sets the online command state when the ER
changes from ON to OFF.
n=2: Sets the offline command state when the ER
changes from ON to OFF. (default)
n=0: Displays communication speed between radio
wave blocks.
n=1: Displays DTE serial communication speed.
(default)
Only n=0 is specifiable. (Can be omitted)
n=0: DR is always ON. (default)
n=1: DR is set to ON at connection of the line (at
establishment of a communication call).
Only n=0 is specifiable. (Can be omitted)
=0: Antenna shows the out of the service area
=1: Zero antenna bars or a single antenna bar
=2: Two antenna bars
=3: Three antenna bars
n=0: Invalidates the incoming call reject/accept setting.
(default)
n=1: Validates the incoming call reject setting
(AT¢DGARL).
n=2: Validates the incoming call accept setting
(AT¢DGAPL).
AT¢DGANSM?: Displays the current setting.
n=0: Adds the APN defined by <cid> to the incoming call
accept list.
n=1: Deletes the APN defined by <cid> from the
incoming call accept list.
Applied to all the cid contents if <cid> is omitted.
AT¢DGAPL?: Displays the incoming call accept list.
n=0: Adds the APN defined by <cid> to the incoming call
reject list.
n=1: Deletes the APN defined by <cid> from the
incoming call reject list.
Applied to all the cid contents if <cid> is omitted.
AT¢DGARL?: Displays the incoming call reject list.
48
Parameter/Explanation
Command execution
example
A/
OK
AT%V
Ver1.00
OK
AT&C1
OK
AT&D1
OK
AT&E0
OK
AT&S0
OK
AT¢DANTE
¢DANTE:3
OK
AT¢DANTE=?
¢DANTE:(0-3)
OK
AT¢DGANSM=0
OK
AT¢DGANSM?
¢DGANSM:0
OK
AT¢DGAPL=0,1
OK
AT¢DGAPL?
¢DGAPL:1
OK
AT¢DGAPL=1
OK
AT¢DGAPL?
OK
AT¢DGARL=0,1
OK
AT¢DGARL?
¢DGARL:1
OK
AT¢DGARL=1
OK
AT¢DGARL?
OK