Panasonic Foma p705im Instruction Manual page 505

Specify Communication Port
1
" (Menu)" of "FOMA PC setup
software"1Select "
setup)".
[Auto-setup (recommended)]
The connected FOMA phone is automatically specified. Usually,
select "Auto-setup".
COM (Specifying COM port)
When specifying a COM port number, specify the COM port
number (COM1 through 99) the FOMA phone is connected to.
≥See page 20 for how to check the COM port number.
2
Click "OK".
The settings are applied.
Select Packet Communication from
" (Easy Setting)"
Using "mopera U" or "mopera" as an access point
This section explains how to make settings for a
high-speed packet communication of 3.6 Mbps maximum.
This setting is for when you use DoCoMo Internet
connection service "mopera U" or "mopera" as a provider.
High-speed packet communication:
You are charged according to the amount of data sent/
received. You can execute data communication without
worrying about time.
High-speed packet communication of up to 3.6 Mbps for
receiving and up to 384 kbps for sending is available.
Note that a communication fee becomes expensive if
you send/receive a large amount of data such as by
browsing web pages having many images, or by
downloading the data.
≥The communication speed for both sending and receiving is up to
384 kbps for "mopera" connection.
1
Click "
2
Select "
(Packet communication (HIGH-SPEED
compatible terminal))", then click "
Confirm that "
communication (HIGH-SPEED compatible terminal))" is checked,
then click " (Next)".
(Communication
(Easy Setting)".
HIGH-SPEED
(Next)".
HIGH-SPEED (Packet
3
Select " mopera U
mopera U)" or " mopera
to mopera)", then click "
To use "mopera U", select " mopera U
mopera U)". To use "mopera", select " mopera
to mopera)".
When " mopera U
the confirmation display appears asking whether you have signed up
for it. If you have signed up, click "
≥See page 13 for using a provider other than "mopera U" or
"mopera".
4
Click "OK".
≥The system obtains the access point name (APN) setting from the
FOMA phone connected to the personal computer. Wait for a while.
5
Enter an access point name, then click "
(Next)".
You can specify any name for the currently created connection.
Enter a plain name in the "
≥You cannot enter the following half-pitch characters:
¥, /, :, ¢, ?, !, <, >, |, and ".
≥For the setting of "
"
≥"mopera U" supports connection types of both "
connection)" and "
select " (IP connection)".
6
Click " (Next)".
If the access point is "mopera U" or "mopera", you can connect even
if the " (user name)" and "
blank.
≥Select a user optionally.
7
Put a check mark for "
(Optimize)", then click "
≥If optimized already, the confirmation display to optimize does not
appear.
8
Confirm the set information, then click "
(Complete)".
The set contents are listed on the display. Confirm that there is no
problem on the set contents, then click "
≥To change the set contents, click "
≥If "
(Create a dial-up shortcut on the desktop)" is checked, a dial-up
shortcut will be created on the desktop.
12
(Connect to
(Connect
(Next)".
(Connect to
(Connect to mopera U)" is selected,
(YES)".
(Connection name)" field.
(caller ID notification)", select
[Not set (recommended)]" for overseas use.
(IP connection)". For overseas use,
(password)" fields are
(Next)".
(Complete)".
(Back)".
(Connect
(PPP