Panasonic Foma p705im Instruction Manual page 545

AT command
AT+CREG=n Sets whether the result is
displayed about the inside and
outside of the service area.
[AT][M]
[&F][&W]
AT+CUSD=n,"<str>",0 Sets or checks the additional
service for network.
[M]
[&F][&W]
AT+FCLASS=n Sets communication class
in the FOMA phone.
[M]
[&F][&W]
AT+GCAP Displays the AT command
supported by FOMA phone.
[M]
AT+GMI Displays the manufacturer name
(Panasonic).
[M]
AT+GMM Displays the product name (FOMA
P705imyu or P705iCL) of the
[M] FOMA phone.
AT+GMR Displays the version of the
FOMA phone.
[M]
AT+IFC=n,m Selects the flow control method. n: DCE by DTE
[M]
[&F][&W]
AT+WS46=n Selects the wireless
communication network of the
FOMA phone.
[M]
[&F][&W]
ATA Performs the receiving process in
the mode when the FOMA phone
[M] received the incoming call.
ATD Performs the automatic outgoing
process to the FOMA phone
according to the contents
specified in the parameter and
[M] dial parameter.
ATEn Sets whether echo-back is
[M] issued to the DTE in the
[&F][&W] command mode.
ATHn Places the FOMA phone into the
on-hook state.
[M]
Outline
n=0: Not notified. (default)
n=1: Notified at switching between the inside and
outside of the service area.
(Inquiry)
AT+CREG?
+CREG: <n>,<stat>
n: Set value
stat:
0: Outside voice call area
1: Inside voice call area
4: Unknown
5: Inside voice call area (during roaming)
n=0: Does not display mid result. (default)
n=1: Displays mid result.
<str>: Service code
Mid result: m,"<str>",0
m=0: Shows the setting is completed.
m=1: Shows the network requires the information.
n=0: Data communication (default)
Result +GCAP: n
n=+CGSM: Some or all GSM commands are supported.
n=+FCLASS: +FCLASS command is supported.
n=+W: +W command is supported.
m: DTE by DCE
0: No flow control
1: XON/XOFF flow control
2: RS/CS (RTS/CTS) flow control
Default: n, m = 2.2
AT+IFC?: Inquires the set value.
Returns "ERROR" for the mode setting because the
wireless communication network is not selected on the
FOMA phone by this command.
n=12: GSM/GPRS
n=22: W-CDMA (Wideband CDMA)
n=25: Automatic
<cid>: 1 to 10
Displays the APN defined by +CGDCONT.
When calling cid1, you can omit the phone number like
"ATD¢99¢¢¢#."
n=0: Issues no echo-back.
n=1: Issues echo-back. (default)
n=0: Disconnects the line. (can be omitted)
52
Parameter/Explanation
Command execution
example
AT+CREG=1
OK
(set to "Notified")
AT+CREG?
+CREG: 1,0
OK
(means the outside of the service
area)
(when moved from the outside to
the inside of the service area)
+CREG: 1
AT+CUSD=0,
OK
AT+CUSD=1,"¢148¢1¢0000#",0
+CUSD:0,"148¢7#",0
OK
AT+FCLASS=0
OK
AT+GCAP
+GCAP:+CGSM,+FCLASS,+W
OK
AT+GMI
Panasonic
OK
AT+GMM
FOMA P705imyu or P705iCL
OK
AT+GMR
Ver1.00
OK
AT+IFC=2,2
OK
AT+WS46=22
ERROR
AT+WS46?
25
OK
RING
ATA
CONNECT
ATD¢99¢¢¢1#
CONNECT
ATE1
OK
(During packet communication)
+++
ATH
NO CARRIER