Olivetti d-Color MF4003 Service Manual page 342

d-Color MF4003/MF3303
• The firmware is downloaded and updated successively. During the firmware download and update, MFP cannot be used.
<Procedure>
1. Select [Download/Update].
2. Touch [Start] to start downloading the firmware.
3. The message to show the status will be displayed on the screen while connecting and transferring data.
4. When the firmware is normally upgraded, the main body will automatically be restarted to complete the Internet ISW.
Download
• To access the program server and download the firmware in accordance with the settings configured in Internet ISW Settings.
• As the firmware is downloaded in the background, MFP can be used during download.
<Procedure>
1. Select [Download].
2. Touch [Start] to start downloading the firmware.
3. The message to show the status will be displayed on the screen while connecting and transferring data. In the middle of downloading, the
task can be cancelled by touching [Cancel].
4. When the firmware download is successfully completed, the result "OK" appears.
Update
• To update the firmware by using the firmware downloaded and saved in the HDD.
• During the firmware download and update, MFP cannot be used.
• This button is not appeared if there is no firmware in the HDD.
<Procedure>
1. Touch [Update].
2. Check the firmware file version in HDD.
3. Touch [Start] to update the firmware.
4. When the firmware is normally upgraded, the main body will automatically be restarted to complete the Internet ISW.
Delete
• To delete the firmware file saved in the HDD.
• This button is not appeared if there is no firmware in the HDD.
<Procedure>
1. Touch [Delete].
2. Touch [Start] to delete the firmware.
18.1.6 Update Start Time Settings
• To set the start time in order to automatically update the downloaded firmware.
NOTE
▪ If updated firmware has not been downloaded by the specified time, firmware update is not performed.
▪ If the main power switch is turned OFF during a firmware update, the firmware is updated next time when the main power switch
is turned ON.
▪ If a job is in process when the specified time comes, the firmware is updated after the completion of the job.
<Procedure>
1. Select [Set] for [Update Firmware at Specified Time].
2. Touch [Hour] and [Min.] and set the firmware update start time.
18.2 Machine Auto Update setting
18.2.1 Auto Update setting
(1) Outline
• "Auto Update" is the function, which makes the main body access the program server periodically through the network to obtain a new
firmware data, then rewrites it automatically.
• To use the Auto Update function, the MFP main body must be connected to such a network environment that the update data can be
downloaded on the network using the SMB or http protocol.
• The Auto Update function will not operate when the MFP main body is under the following conditions.
• Main power switch is set to OFF.
• Sub power OFF mode (power key is orange) or ErP auto power OFF mode (power key flashes orange) enabled
• [Administrator] -> [Security] -> [Enhanced Security Mode] is set to "ON".
• MFP is operating, or there are jobs present (including appointed jobs).
• MFP is in idle with suspended job.
• Trouble has occurred.
• Image file is in the memory.
• Model or the circuit board of the program does not match.
(2) Preparations
• For using this function effectively, before executing the following procedures contact with the administrator to obtain an agreement.
• Set the network parameter, program server address as well as firewall address to the MFP main body.
• Create a program update information file (C_UpdateList.ini) and store a set of data for updating in the program server.
Creating the program update information file (C_UpdateList.ini)
• Specify the firmware, loadable driver, configuration files as shown below.
NOTE
▪ [FirmWare], Version, FilePath, [LoadableDriver], NumberOfFiles, [Config], [Option], [QuickUpdate] and Update must be
specified by using the capital letters and small letters properly.
Service Manual
I SERVICE MODE > 18. Machine Update Setting
I-126
Y119930-3