Olivetti d-Color MF4003 Service Manual page 263

d-Color MF4003/MF3303
10.5.11 SW No.135
• Setting for ID length of the HID Prox card
Bit Assignment
00000000
00000001
10.5.12 SW No.143
• Expansion setting of the touch panel sensitive area when the web browser function is used
Bit Assignment
00000000
00000001
00000010
NOTE
▪ The sensitive area of the control panel can be expanded by selecting "16 dots" or "9 dots" on the software switch No.143. Note
that the control panel's sensitive area expanded in this manner may not detect touches properly.
10.5.13 SW No.145
HEX 01
• Switching to Auto detection for paper size in manual bypass tray
Bit Assignment
00000000
00000001
HEX 02
• Switching paper feed mode if the size of paper fed from the manual bypass tray is mismatched
Bit Assignment
00000000
00000010
HEX 04
• Displaying message when the paper size in manual bypass tray is mismatched with the paper size specified on the control panel
Bit Assignment
00000000
00000100
HEX 08
• When running a copy cycle with originals placed on the original glass, and [Auto] is displayed in "Group/Sort" of the finishing function,
[Auto] will be set as default. ("Sort" and "Offset" will be executed when [Auto] is selected.)
Bit Assignment
00000000
00001000
HEX 10
• Switch-over settings of Duplex printing and Billing permission
• Setting for allowing/prohibiting billing on exited paper when a paper size error occurred at the time of duplex printing
Bit Assignment
00000000
00010000
10.5.14 SW No.146
HEX 04
• Setting for enabling use of Non-Image Area Erase, Centering, and Original Size when the book original is used in the fax/scanner mode
Bit Assignment
00000000
00000100
Y119930-3
HEX Assignment
00 Reports that the 1st byte shows the ID length of the card, the
2nd byte and after shows the card ID.
01 Reports the card ID with the ID length including the 1st byte.
HEX Assignment
00 26 dots: 26 dots from the perimeter of the touch panel is a
nonsensitive area.
01 16 dots: 16 dots from the perimeter of the touch panel is a
nonsensitive area.
02 9 dots: 9 dots from the perimeter of the touch panel is a
nonsensitive area.
HEX Assignment
00 Enable
01 Disable
HEX Assignment
00 Stop immediately
02 Stop accordingly
Stop immediately in the following cases as an exception.
• "1" is set at bit4 for the Switch No.145
• For jobs where center stapling, half-folding, tri-folding
and Z-folding are set with a finisher equipped
HEX Assignment
00 Enable
04 Disable
HEX Assignment
00 Enable
08 Disable
HEX Assignment
00 Allow (billing on one side of the paper)
10 Prohibit
HEX Assignment
00 Prohibits use of Non-Image Area Erase, Centering, and
Original Size.
04 Enables use of Non-Image Area Erase, Centering, and
Original Size.
Details
Details
Details
Details
Details
Details
Details
Details
I-47
I SERVICE MODE > 10. System 2
Default value (Bit/HEX)
00000000 / 00
Default value (Bit/HEX)
00000000 / 00
Default value (Bit/HEX)
00000000 / 00
Default value (Bit/HEX)
00000010 / 02
Default value (Bit/HEX)
00000000 / 00
Default value (Bit/HEX)
00000000 / 00
Default value (Bit/HEX)
00000000 / 00
Default value (Bit/HEX)
00000000 / 00
Service Manual