Olivetti d-Color MF 552 plus Installation Manual

Olivetti d-Color MF 552 plus Installation Manual

Hide thumbs Also See for d-Color MF 552 plus:

Advertisement

d-Color MF 362 plus/d-Color MF 282 plus/d-Color MF 222 plus
© Olivetti S.p.A
<Important>
Be sure to correctly follow the procedures in order as explained in this Installation Manual.
If you do not follow the procedure in order, the image trouble may occur.
I. Outline of installation procedures (d-Color MF 552 plus/d-Color MF 452 plus)
AU-102
WT-506
*2
AU-201
PK-519
When installing the machine and associated options as a system, follow the order shown on the upper.
Caution:
• For the detailed installation procedures for each
option, follow the instructions given in the corre-
sponding installation manual and perform the
procedures correctly. (Optional devices must be
installed after completing the main unit installa-
tion.)
• Once the Power Switch is turned ON, do not
turn OFF it until the installation work has been
completed.
• When placing the machine on the floor, make
sure to use the paper feed cabinet to secure the
performance and the quality of the product.
• Lifting the machine in an awkward position or
transporting it in a poorly balanced position
could result in personal injury. When transport-
Y115290-3
Y115290-3
d-Color MF 552 plus/d-Color MF 452 plus/

INSTALLATION MANUAL

Applied Machines: d-Color MF 552 plus/d-Color MF 452 plus/d-Color MF 362 plus/
KP-101
HT-509
TK-101
MK-734
PC-110
PC-210
SP-501
Machine
Electronic system options
MK-735
*1
AU-201
KH-102
FS-533
OT-506
PK-521
SD-512
d-Color MF 282 plus/d-Color MF 222 plus
PC-410
MK-730
LU-204
LU-301
*1
: When installing the AU-201 with MK-735
*2
: When installing the AU-201 without MK-735
*3
: No particular order in installation procedures.
*4
: Unable to be installed in d-Color MF 452 plus.
*4
JS-506
ZU-606
*4
*4
FS-535
*4
ing the machine, assign an adequate number of
persons to the job and ensure that each person
can take a good position of not being exces-
sively loaded.
(mass: approx. 101 kg (222-11/16 lb))
E-1
✱ Electronic system options
*3
EK-606
EK-607
*3
UK-204
*3
SC-508
*3
UK-208
FK-511
VI-506
IC-414
PK-520
FS-534
SD-511
*4
JS-602
*4
PI-505
A2XKIXC001DA
Installation Manual
Installation Manual
*3

Advertisement

Table of Contents
loading

Summary of Contents for Olivetti d-Color MF 552 plus

  • Page 1: Installation Manual

    MF 552 plus/d-Color MF 452 plus/ d-Color MF 362 plus/d-Color MF 282 plus/d-Color MF 222 plus INSTALLATION MANUAL Applied Machines: d-Color MF 552 plus/d-Color MF 452 plus/d-Color MF 362 plus/ © Olivetti S.p.A d-Color MF 282 plus/d-Color MF 222 plus <Important>...
  • Page 2 Outline of installation procedures (d-Color MF 362 plus/d-Color MF 282 plus/d-Color MF 222 plus) ✱ Electronic system options KP-101 EK-606 EK-607 HT-509 MK-734 UK-204 UK-208 UK-209 PC-110 PC-210 PC-410 SC-508 AU-102 WT-506 Machine MK-730 FK-511 AU-201 Electronic system options VI-506 MK-735 IC-414 : When installing the AU-201 with MK-735...
  • Page 3 II. Installation space (unit: mm (inch)) III. Pre-installation check items d-Color MF 552 plus + PC-210 + ZU-606 + FS-535 1. Select a level and stable place for installing the machine. + LU-204 2. Be sure to use a power source of the voltage and 2763 frequency indicated in the product specifications.
  • Page 4: Accessory Parts

    15. Chart 16. Spacer 17. Stylus pen 18. Waste toner box d-Color MF 552 plus/d-Color MF 452 plus: One d-Color MF 362 plus/d-Color MF 282 plus/d-Color MF 222 plus: Two d-Color MF 362 plus/d-Color MF 282 plus/d-Color MF 222 plus only...
  • Page 5: Removing The Machine

    After removing protective tape A, be sure to push Machine mass the area indicated by the “ ” mark to lock the d-Color MF 552 plus/d-Color MF 452 plus: approx. guide. (d-Color MF 552 plus/d-Color MF 452 plus 101 kg/222-11/16 lb only) d-Color MF 362 plus/d-Color MF 282 plus/d-Color <d-Color MF 552 plus/d-Color MF 452 plus>...
  • Page 6 2. Open the right door and remove the protective sheet and packaging materials. <d-Color MF 362 plus/d-Color MF 282 plus/ Note: d-Color MF 222 plus> After removing the packaging materials, make sure that the transfer roller assy is secured in place.
  • Page 7 5. Slide out the tray 1 and remove the protective 8. <d-Color MF 552 plus/d-Color MF 452 plus> tape from the inside of the tray. Open the lower front door. A5C1IXC005DA A2XKIXC010DA 6. Slide out the tray 2 and remove the tray locking <d-Color MF 362 plus/d-Color MF 282 plus/d-...
  • Page 8 9. <d-Color MF 552 plus/d-Color MF 452 plus> 11. Remove the protective materials from the four places. Remove the protective tape. Note: Keep the protective materials. It is necessary for Protective tape transporting the machine. A2XKIXC011DA <d-Color MF 362 plus/d-Color MF 282 plus/d- Color MF 222 plus>...
  • Page 9: Installing The Toner Cartridge

    2. Insert the toner cartridge into the machine. Note: * Perform the following steps 17 to 19 only when installing d-Color MF 552 plus/d-Color MF 452 • Make sure that the color is same between plus. inserting port and the toner cartridge.
  • Page 10 Only d-Color MF 362 plus/d-Color MF 282 plus/d- tridges for other colors of toner. Color MF 222 plus needs this step. 5. <d-Color MF 552 plus/d-Color MF 452 plus> Close the upper front door. <d-Color MF 362 plus/d-Color MF 282 plus/d- Color MF 222 plus>...
  • Page 11 X. Connecting the power cord XII. Adjusting touch panel 1. Connect the power cord. 1. Press the Menu key. 2. Touch “Accessibility.” 3. Touch “Touch Panel Adjustment.” 4. Using the stylus pen, lightly touch the center of the + markers at four places on the touch panel. (Any specific marker can be the first one.) Note: Pressing the touch panel hard may cause dam-...
  • Page 12 <If A3 or Ledger paper is set in step 1> 11. Touch “Copy”, select “A3 ”, and press the start key. 6. Touch “Printer”, select “A3 ”, and A test pattern will then be produced on the press the start key. or Ledger paper.
  • Page 13 ½ x 11 <If A4 or Letter paper is set in step 1> 11. Touch “Copy”, select “A4 ”, and press the start key. ½ x 11 6. Touch “Printer”, select “A4 ”, and A test pattern will then be produced on the two press the start key.
  • Page 14 XV. Date/Time setting (Service Mode) XVIII. Unit change 1. Make sure that the Service Mode screen is dis- Note: played. This function allows the user to select the type of 2. Display the Date & Time Setting screen. message that will appear when the replacement (To display the Date &...
  • Page 15: Adjusting The Height

    XX. Adjusting the height 2. If there is any clearance, adjust the height by turning the adjustment screw on the right side viewed from the back. Note: Clockwise: The rear side will move up. • The following “XX. Adjusting the height” to Counterclockwise: The rear side will move down.
  • Page 16 3. Place the chart in the document feeding tray (with 8. When the difference of the deviation is + (plus), the side having an arrow facing up). turn the adjustment screw located at the back of the dual scan document feeder clockwise to adjust.
  • Page 17 9. When the difference of the deviation is - (minus), 3. Fold all 5 sample copies as illustrated and check turn the adjustment screw located at the back of for any deviation. the dual scan document feeder counterclockwise Deviation on the sample will be Z. to adjust.
  • Page 18: Magnification Adjustment

    XXIII. Magnification adjustment 8. Loosen the two screws shown in the illustration. <Magnification in the feeding direction> Note: Perform this adjustment if necessary. 1. Place the chart in the document feeding tray (with the side having an arrow facing up). A3CEIXC034DA 9.
  • Page 19 9. Touch “END.” 16. Display the Service Mode screen. 10. Touch “Exit” on the Service Mode screen. (For details of how to display the Service Mode 11. Turn OFF and ON the Main Power Switch. screen, see the service manual.) 17.
  • Page 20 XXIV. Mixed original size adjustment 27. Check whether the difference in the width D between the chart and the copy sample is within Note: the specified range. Perform this adjustment if necessary. Difference in the width D = D of the copy sample –...
  • Page 21 3. Place the chart in the document feeding tray. 12. Touch “Exit” on the Service Mode screen. (Make sure that the blank surface of the chart 13. Turn OFF and ON the Main Power Switch. faces up.) Note: When displayed the Service Mode screen, be sure to turn off the main power after exiting the Service Mode screen and wait for 10 seconds or more before turning on.
  • Page 22 XXVI. Affixing the label (Legal restrictions 19. Check whether the difference in the width A between the chart and the copy sample is within on copying) the specified range. Difference in the width A = A of the copy sample Affix the label (Legal restrictions on copying) to the –...
  • Page 23: Affixing The Paper Size Label

    XXVIII. Affixing the paper size label XXX. Connecting the network cable Affix the paper size labels that correspond to the 1. Connect the networking equipment (HUB) using sizes of paper used in each tray. the network cable. Note: The following shows the recommended network cables that correspond to each communication speed.
  • Page 24 4. Route the network cable through the harness 5. Route the network cable through the harness guides and pass it through the notch cut in step 3. guides and three wire saddles. Note: Note: Leave an appropriate amount of slack in the por- Leave an appropriate amount of slack in the por- tion of the cable between the plug and the top har- tion of the cable between the plug and the top har-...
  • Page 25 Method and make the following settings. Note: IP Address: IP address of the controller • <d-Color MF 552 plus/d-Color MF 452 plus> Subnet Mask: Subnet mask of the network, to Open fully the dual scan document feeder. which the machine is connected <d-Color MF 362 plus/d-Color MF 282 plus/d-...
  • Page 26 XXXIII. Adjusting registration of paper 10. If the measured width A falls outside the speci- fied range, enter the correction value using the source options key. Note: * When the tray 4 is available with the optional Performing this procedure is necessary only when paper feed cabinet, check the tray and make the paper feed cabinet PC-110/PC-210/PC-410 is adjustments in the same way.
  • Page 27 XXXV. Affixing the panel sheet XXXVI. Installing the output tray (OT-506) (d-Color MF 552 plus/d-Color MF 452 plus Affix the supplied panel sheet to the surface of the operation panel. only) Note: 1. Open the upper and lower front door of the •...
  • Page 28: Accessory Parts

    SP-501 Stamp Unit INSTALLATION MANUAL Applied Machines: d-Color MF 552 plus/d-Color MF 452 plus COLOR MFP: 55 ppm/45 ppm Product Code: A5AY/A5C0 I. Accessory parts 4. Remove the cover shown in the illustration. (Two screws) Name Shape Q’ty 1. Stamp unit 4614U001AA 2.
  • Page 29 8. Remove the ground terminal. (One screw) 13. Route the ground terminal through the hole shown in the illustration and attach the guide plate to the dual scan document feeder. (One screw removed in step 7) Screw A3CEIXC028DA 9. Mount the supplied stamp in stamp unit. Note: Align the round pin of the stamp with the slit in the stamp unit side.
  • Page 30 OC-511 Original Cover INSTALLATION MANUAL Applied Machines: d-Color MF 362 plus/d-Color MF 282 plus/d-Color MF 222 plus COLOR MFP: 36 ppm/28 ppm/22 ppm Product Code: A5C1/A5C2/A5C4 I. Accessory parts II. Installation procedures 1. Remove the two knockouts using nippers or a Name Shape Q’ty...

Table of Contents