Olivetti d-Color MF4003 Service Manual page 194

d-Color MF4003/MF3303
Key name
Timer Reservation TX Report
Confidential Rx Report
Remark Column Print Setup
Network Fax RX Error Report
Print Job Number
MDN Message
DSN Message
Print E-mail Message Body
Legend display Settings
6.10.6 Multi Line Settings
NOTE
▪ It will be displayed each only when fax kit (line 2 or line 3 or line 4) is mounted.
Key name
PC-Fax TX Line Setting
Fax Line 2
Fax Line 3
Fax Line 4
6.10.7 Network Fax Setting
Key name
Black Compression Level
Color/Grayscale Multi-Value
Compression Method
Internet Fax RX Ability
I-Fax Advanced Setting
IP Address Fax Operation Settings
6.10.8 Header Information
Key name
Header Information
6.10.9 Fax Print Quality Settings
Key name
Fax Print Quality Settings
6.10.10 Fax Setting List
Key name
Fax Setting List It will not be displayed when [Service Mode] -> [Billing Setting] -> [Management Function Choice] shows that the
"Vendor 2" is mounted. (It will be displayed when the Key Counter is mounted or [Service Mode] -> [System 2] ->
[Software Switch Setting] shows that switch No.33 is set to [00000001] at Bit assignment/[01] at HEX assignment.)
6.11 Copier Settings
Key name
Basic Setting
Service Manual
-
-
Setting will be available when [IP Address Fax Function Settings] or [I-Fax Function Setting] is set to "ON"
in [Administrator] -> [Network] -> [Network Fax Setting] -> [Network Fax Setting].
• It will not be displayed when [Report Addition Information] is set to "Diagnosis Code" or "Dial Number"
by [Service Mode] -> [FAX] -> [List Output].
• It will not be displayed when [Service Mode] -> [System 2] -> [Software Switch Setting] shows that
switch No.77 is set to [00000100] at Bit assignment/[04] at HEX assignment.
It will be displayed when [Administrator] -> [Network] -> [Network Fax Setting] -> [Network Fax Setting] ->
[I-Fax Function Setting] is set to "ON."
-
• It will be not displayed when [PC-Fax Permission Setting] is set to "Restrict" in [Administrator] -> [Fax
Settings] -> [Function Setting].
• Line 2 to 4 will be displayed when [Administrator] -> [Fax Settings] -> [Multi Line Settings] -> [Fax Line 2 to 4]
-> [Multi Line Usage Setting] -> [Line 2 to 4 Setting] is set to "TX and RX" or "TX Only."
Line Parameter Setting Dialing Method
Number of RX Call Rings
(Receive Time Interval
Setting)
Line Monitor Sound
Pause Time
Function Setting Number Display Function
(Only for Japan)
Multi Line Usage Setting Line Setting
Sender Fax No.
It will be displayed when either [IP Address Fax Function Settings] or [I-Fax Function Setting] is set to
"ON" in [Administrator] -> [Network] -> [Network Fax Setting] -> [Network Fax Setting].
It will be displayed when [Administrator] -> [Network] -> [Network Fax Setting] -> [Network Fax
Setting] -> [I-Fax Function Setting] is set to "ON."
It will be displayed when [Administrator] -> [Network] -> [Network Fax Setting] -> [Network Fax
Setting] -> [IP Address Fax Function Settings] is set to "ON."
-
-
Auto Zoom (Platen)
Function/Precondition
Function/Precondition
-
When [Service Mode] -> [FAX] -> [Line 2 to 4] ->
[Network] -> [Network Setting 1] -> [Receive Signal
Detection Mode] is set to "Time", [Receive Time
Interval Setting] will be displayed.
-
-
-
-
-
Function/Precondition
Function/Precondition
Function/Precondition
Function/Precondition
Function/Precondition
-
H-26
H UTILITY MODE > 6. Administrator
Y119930-3