Global: Page Menu Commands - Korg NAUTILUS Series Parameter Manual

GLOBAL mode

GLOBAL: Page Menu Commands

Compare
Write Global Setting
Set Program Bank Type
Change all bank references
Touch Panel Calibration
Half Damper Calibration
LCD Setup
Update System Software
Display Public ID
Auto Power-Off Setting...
Fan Control Setting
Rear Panel Illumination Setup
Select All
Unload all in bank
Remap MS/Sample Banks
Dump Program
Dump Combination
Dump Drum Kit
Dump Wave Sequence
Dump Global Setting
Dump Sequencer
Dump Set List
Dump Drum Track Pattern
Dump Arpeggio Pattern
System Exclusive Data Dumps
Reset Controller MIDI Assign
Copy Scale
Clear Special Function Assignments
Write Wave Sequence
Write Drum Kit
Copy Key Setup
Swap Key Setup
Write Arpeggio Patterns
Rename Arpeggio Pattern
Copy Arpeggio Pattern
Uninstall EXs
PAGE
MODE
Write Global Setting
This command writes most of the GLOBAL mode settings,
with the following exceptions.
• Drum Kits and Wave Sequences are written separately,
with their own commands; see "Write Drum Kit" on
page 691 and "Write Wave Sequence" on page 690.
• The Effect Global SW settings are not written.
Also, a few settings are saved automatically as soon as they
are edited, without need to write the Global Settings,
including:
• Auto Power-Off Setting
• Fan Control Setting
• Rear Panel Illumination Setup
• KSC Auto-Load settings
To use the Write Global Setting command:
1. Select Write Global Setting to open the dialog box.
684
→p.112
→p.684
→p.684
→p.685
→p.685
→p.685
→p.686
2. To write the data, press the OK button. To cancel
→p.686
without writing, press the Cancel button.
→p.687
Do not turn off the power for at least 10 seconds after
→p.687
using the Write Global Setting command. This allows
→p.687
the system time to complete the process, which includes
→p.688
saving a backup of the data to the internal drive.
→p.688
→p.688
Set Program Bank Type
→p.125
→p.688
This command lets you do two related things:
→p.688
• Set the bank types of each of the Program banks (except
→p.688
for GM) to either HD-1 or EXi
→p.688
• Initialize banks of Programs
→p.688
When you execute this command, the Programs within the
→p.688
specified banks will be initialized to Programs of the
→p.688
selected bank type.
→p.688
Note that bank types are set automatically when loading
→p.688
Program banks from drive; you don't need to use this
→p.689
command first.
→p.690
Before you use this command, make sure that Memory
→p.690
Protect is disabled for Programs (see "0–1e: Memory
→p.690
Protect" on page 635). Otherwise, the message "Memory
→p.690
Protected" will appear after you press OK, and no
→p.691
changes will be made.
→p.691
1. Choose "Set Program Bank Type" to open the dialog
→p.691
box.
→p.691
→p.691
→p.691
→p.692
→p.126
→p.126
This indicates the current type for each bank.
2. Specify the bank type for each bank.
No Change: The bank type will not be changed, and the
bank's Program data will remain unchanged.
HD-1: The bank type will be set to HD-1, and all of the
bank's Programs will be initialized.
EXi: The bank type will be set to EXi, and all of the
bank's Programs will be initialized.
Note: If a bank is set to anything other than No Change,
all data in that bank will be initialized – even if you have
specified the same bank type as before. If you want to
keep your data, you must first use Save All or Save PCG
to save it.
3. Press the OK button to execute, or press the Cancel
button to cancel. A dialog box will ask you to confirm
the operation.