Table of Contents
Advertisement
Effect Guide
Routing
You can use up to twelve channels (IFX 1...12) for the Insert
Effects in any mode.
PROGRAM mode
Use Bus Select (PROGRAM 8–1c) to set the destination bus
of the oscillator output.
L/R: Send the output to the L/R bus. Instead, it is sent to
AUDIO OUTPUT (MAIN) L/MONO and R after the TFX1
and 2.
IFX1...12: The signal is sent to Insert Effects IFX 1–12.
1...4, 1/2...3/4: The signal is sent to the selected Individual
Output. For more information, please see "Individual
Outputs" on page 757.
Off: The output will not be sent to the L/R bus, IFX1–12
buses, or Individual 1–4 buses. Choose the Off setting if you
want to connect the oscillator output to a master effect in
series. Use Send1 (to MFX1) and Send2 (to MFX2) to
adjust the send level.
Use Send1 (to MFX1) and Send2 (to MFX2) (PROGRAM
8–1f) to specify the send level for the Master Effects. This
setting is effective if Bus Select (PROGRAM 8–1c) is set to
L/R or Off.
If Bus Select is set to IFX1–12, use Send1 and Send2
(PROGRAM 8–5a) to specify the send level of the post-IFX
signal.
Send1 responds to CC#93, and Send2 responds to
CC#91. At this time, the actual send level uses the value
of the Send 1 and 2 settings for Oscillators 1 and 2,
multiplied by the Send 1 and 2 values received via MIDI.
In the example shown in the diagram (Fig. 2–1a), Oscillators
1 and 2 outputs being sent to IFX1.
If you are connecting the Insert Effects in series, check the
Chain box (PROGRAM 8–5a). Use Chain to (PROGRAM
8–5a) to specify the destination to which the signal will be
chained.
Fig. 2–1a
738
If you check the IFX1 checkbox, the output of IFX1 will be
sent to the input of the IFX you specify in "Chain to."
Effects can be chained only in ascending order of their
number; for example IFX1 can be chained to IFX2 through
IFX12, and IFX2 can be chained to IFX3 through IFX12.
You can create a chain of up to twelve insert effects in series,
IFX1 through IFX12.
When the Insert Effects are connected in series, the values of
the Pan (CC#8), Bus Sel., REC Bus, Send1, and Send2
parameters for the post-IFX signal will be used.
In the example shown in the diagram (Fig. 2–1b), the Chain
check box is checked, and each Chain to parameter is set to
the subsequent effect, creating a series connection of IFX1
→ IFX2 → IFX3 → IFX4 → IFX5 → IFX6 → IFX7 →
IFX8 → IFX9 → IFX10 → IFX11 → IFX12. The post-
IFX12 settings for Pan (CC#8), Bus Select, REC Bus,
Send1, and Send2 will be used.
Settings for drum programs
If you have selected "Drums" for Oscillator Mode
(PROGRAM 1–1b) of a Program, the "Use DKit Setting"
box (PROGRAM 8–1b) becomes available. For more
information, please see diagram Fig. 2–1c.
If you check this box, Bus Select FX Control Bus, Send1,
and Send2 (GLOBAL 5–3b) for each key of the selected
DrumKit becomes effective. For example, you can send a
snare sound to IFX1 to apply the Gate effect, a kick sound to
IFX2 to apply EQ, and other sounds to AUDIO OUTPUT
(MAIN) L/MONO and R without applying any Insert
Effects.
Tip: In most of the preloaded drum kits, the following types
of drum instrument have the same Bus Select settings.
Snares → IFX1
Kicks → IFX2
Toms → IFX3
Cymbals → IFX4
Percussion etc. → IFX5
Advertisement
Table of Contents
