Table of Contents
Advertisement
Copy from Combi
This command copies the parameters of the specified
combination to the setting data of the currently selected
song.
Note: Only the timbres used by the combination will be
copied. Timbres in the combination whose Status is Off will
not be copied. If any timbres are set to Mute, the
corresponding tracks of the song will be set to a Status of
Off. However if none of the timbres used in the combination
have a MIDI channel setting of Gch, a MIDI track whose
MIDI channel is Gch will automatically be specified, and
that track will be selected in Track Select. After the copy is
executed, you will immediately be able to play in the same
state as that combination.
1. Select "Copy from Combi" to open the dialog box.
2. In "Combination," select the copy source destination.
3. Use the IFX-All, IFX-All used, MFXs and TFXs check
boxes to specify whether you want the effect settings
of the combination to be copied as well.
IFX-All: All insert effect settings of the copy-source
combination (the contents of the Insert FX page and the
IFX1–12 effect parameters) will be copied.
IFX-All used: Only the insert effects that are used by the
copy-source combination will be copied. When copied,
they will be packed into unused slots (000: No Effect,
unless within a chain).
Note: Copy-source insert effects that are set to 000: No
Effect will not be copied. However if 000: No Effect is
included within a chain, it will be copied.
If an entire chain in the copy-destination consists of 000:
No Effect, it will be used as a copy-destination.
MFXs: All master effect settings of the copy-source
combination will be copied.
TFXs: All total effect settings of the copy-source
combination will be copied.
4. Specify the desired Multi REC Standby setting.
On: The Status will automatically be set to REC for
MIDI tracks corresponding to valid timbres in the copy-
source combination. In addition, "Multi REC" (0–1a) will
automatically be turned on, and Recording Setup (0–5a)
will be set to Overwrite.
5. To execute the Copy operation, press the OK button.
To cancel, press the Cancel button.
SEQUENCER: Page Menu Commands Copy from Combi
Copy From Program
This command copies settings from the program you specify
to the currently selected song.
This is the same function as in COMBINATION mode; for
details, see "Copy From Program" on page 433.
This command in SEQUENCER mode differs from its
behavior in COMBINATION mode in that the channels
assigned to the tracks of the song will be preserved
regardless of the "Overwrite ARP/DRUM" setting of the
copy-destination track's "MIDI Channel." (See step 4.)
Stereo Pair
This lets you assign adjacent audio tracks as a stereo pair.
The following parameters of paired channels will be linked
with the same values.
Volume, Send1, Send2, EQ (Bypass, Input Trim, Low Gain,
Mid Cutoff, Mid Gain, High Gain), Play/Rec/Mute
In addition, you can use the Track Edit page menu
commands to edit paired tracks simultaneously.
Paired channels are controlled by the odd-numbered knob
or slider. Moving the even-numbered knob or slider will
not control the channels.
1. Select Stereo Pair to open the dialog box.
2. Use Audio Track 1&2, 3&4, 5&6, 7&8, 9&10, 11&12,
13&14, and 15&16 to specify the audio tracks that you
want to pair.
Uncheck audio tracks that you want to un-pair.
3. Specify the "Pan Mode."
Individual: The pan of the two channels will operate
independently.
Balance: The pan of the two channels will operate as a
balance control.
4. To apply the changes you made, press the OK button.
If you decide to cancel, press the Cancel button.
Optimize RAM
This command optimizes the RAM memory. When you
execute this command, unused memory areas will be
reorganized, allowing the full amount of remaining to be
used. For more information, see "Optimize RAM" on
page 114.
525
Advertisement
Table of Contents
