Table of Contents
Advertisement
R Delay Base Note
This sets the basic length of the Right Delay, relative to the
BPM setting.
Times
This multiplies the length of the Right Delay's Base Note.
L Depth
Sets the amount of pitch modulation for the left channel.
0...100 produce chorus-like effects; over 100 produces more
obvious pitch-shifting.
R Depth
Sets the amount of pitch modulation for the right channel.
097: St. BPM Auto Panning Dly
This stereo auto panning delay enables you to set the delay
time to match the song tempo.
Stereo In - Stereo Out
Left
High Damp Low Damp
Delay
Feedback
Delay
High Damp Low Damp
Right
Tempo
BPM
Base Note x Times
BPM
Base Note x Times
LFO: Tri / Sin
LFO Shape
DELAY
BPM
MIDI syncs to the system tempo; 40-240 sets the tempo
manually for this individual effect.
Time Over? L >
Time Over? R >
The maximum delay time is 1,360msec per channel (left and
right). If the channel's combination of BPM, Base Note, and
Times exceeds this limit, the error message "OVER!" will
appear. If this occurs, change the delay time parameters so
that this message no longer appears.
L Delay Base Note
This sets the basic length of the Left Delay, relative to the
BPM setting. The values range from a 32nd note to a whole
note, including triplets.
Times
This multiplies the length of the Base Note. For instance, if
the Base Note is set to a sixteenth note, and Times is set to 3,
the delay length will be a dotted eighth note.
R Delay Base Note
This sets the basic length of the Right Delay, relative to the
BPM setting.
Times
This multiplies the length of the Right Delay's Base Note.
[ ... ]
[x1...x32]
[0...200]
[0...200]
Wet / Dry
Pan
Depth
Pan
Wet / Dry
LFO Phase
[MIDI, 40.00...300.00]
[---, OVER!]
[---, OVER!]
[ ... ]
[x1...x32]
[ ... ]
[x1...x32]
Delay 097: St. BPM Auto Panning Dly
L Feedback
Sets the amount of feedback for the left delay. Negative
values invert the phase.
R Feedback
Sets the amount of feedback for the right delay.
OUTPUT
This is the standard effects output section, with modulatable
control over wet/dry balance. For more information, see
"OUTPUT" on page 762.
L Feedback
Sets the feedback amount for the left channel.
R Feedback
Sets the feedback amount for the right channel.
High Damp [%]
Sets the amount of high-frequency attenuation.
Low Damp [%]
Sets the amount of low-frequency attenuation.
LFO
Waveform
Selects the LFO Waveform.
Shape
Changes the curvature of the LFO Waveform. For more
information, see "Shape" on page 782.
Phase [degrees]
Sets the LFO phase difference between the left and right. For
more information, see "Phase [degrees]" on page 817.
Frequency [Hz]
This sets the LFO speed, in Hz. It applies only when
MIDI/Tempo Sync, below, is Off.
MIDI/Tempo Sync
BPM
Base Note
Times
When MIDI/Tempo Sync is on, the LFO speed is set by
BPM, Base Note, and Times, instead of Frequency. For
more information, see "MIDI/Tempo Sync" on page 779.
Type
[Individual, Common1, Common2]
This controls whether the effect uses its individual LFO, or
one of the Common FX LFOs. For more information, see
"LFO Type" on page 779.
Common LFO Phase Offset [degrees]
When Type is set to Common FX LFO 1 or 2, this lets you
offset the phase from the master LFO.
[+/–100]
[+/–100]
[+/–100]
[+/–100]
[0...100]
[0...100]
[Triangle, Sine]
[+/–100]
[–180...+180]
[0.02...20.00]
[Check-box]
[MIDI, 40.00...300.00]
[ ... ]
[x1...x32]
[+/–180]
851
Advertisement
Table of Contents
