Mono-Mono Serial - Korg NAUTILUS Series Parameter Manual

Mono-Mono Serial

109: P4EQ - Exciter through 140: Reverb - Gate provide
serial chains of mono effects. These include various
combinations of EQ, Compressor, Limiter, Exciter,
Overdrive, Wah, Chorus/Flanger, Phaser, Multitap Delay,
Gate, and Reverb, as described below.
PARAMETRIC EQ
For a description of the on-screen EQ graphic, see "011:
Stereo Parametric 4EQ" on page 774.
Trim
Sets the parametric EQ input level.
Band1 Fc [Hz]
Sets the center frequency of Band 1.
Q
Sets the bandwidth of Band 1. For more information, please
see "Q" on page 774.
Gain [dB]
Sets the gain of Band 1.
Band2 Fc [Hz]
Sets the center frequency of Band 2.
Q
Sets the bandwidth of Band 2.
Gain [dB]
Sets the gain of Band 2.
Band3 Fc [Hz]
Sets the center frequency of Band 3.
Q
Sets the bandwidth of Band 3.
Gain [dB]
Sets the gain of Band 3.
Band4 Fc [Hz]
Sets the center frequency of Band 4.
Q
Sets the bandwidth of Band 4.
Gain [dB]
Sets the gain of Band 4.
EXCITER
Emphasis Frequency
Sets the frequency range to be emphasized. For more
information, see "Emphasis Frequency" on page 777.
Exciter Blend
Sets the intensity (depth) of the Exciter effect. For more
information, see "Blend" on page 777.
860
MULTITAP DELAY
Tap1 Time [msec]
Sets the Tap1 delay time.
Tap2 Time [msec]
Sets the Tap2 delay time.
Tap1 Level
Sets the Tap1 output level. For more information, see "Tap1
Level" on page 836.
[0...100]
Feedback (Tap2)
Sets the Tap2 feedback amount.
[20...1.00k]
High Damp [%]
Sets the amount of high-frequency attenuation.
[0.5...10.0]
Wet/Dry
Sets the multitap delay effect balance. For more information,
see "Pan" on page 827.
[–18...+18]
Source
Selects the Wet/Dry modulation source for the multitap
[50...5.00k]
delay.
Amount
[0.5...10.0]
Sets the Wet/Dry modulation amount for the multitap delay.
[–18...+18]
COMPRESSOR
For details on the Compressor graphics, see "001: Stereo
[300...10.00k]
Dyna Compressor" on page 761.
Sensitivity
[0.5...10.0] Sets the sensitivity. For more information, see "Sensitivity"
on page 761.
Attack
[–18...+18]
Sets the attack level. For more information, see "Attack" on
page 762.
[500...20.00k]
Output Level
Sets the compressor output level. For more information, see
[0.5...10.0]
"OUTPUT" on page 762.
LIMITER
[–18...+18]
For details on the Limiter graphics, see "005: Stereo
Limiter" on page 768.
Ratio
Sets the signal compression ratio. For more information, see
[0...70]
"Ratio" on page 763.
Threshold [dB]
Sets the level above which the compressor is applied. For
[+/–100]
more information, see "Threshold [dB]" on page 763.
Attack
Sets the attack time. For more information, see "Attack
[msec]" on page 764.
[0.0...1360.0]
[0.0...1360.0]
[0...100]
[+/–100]
[0...100]
[Dry, 1:99...99:1, Wet]
[Off...Tempo]
[+/–100]
[1...100]
[1...100]
[0...100]
[1.0:1...50.0:1, Inf:1]
[–40...0]
[1...100]